RP40-2412SGW Recom Power Inc, RP40-2412SGW Datasheet - Page 4

• Manufacturer Part Number: RP40-2412SGW
• Description: CONV DC/DC 40W SNGL 12V OUT
• Manufacturer: Recom Power Inc
• Series: Powerline RP40-GWr
• Type: Isolatedr

Specifications of RP40-2412SGW

• Output: 12V
• Number Of Outputs: 1
• Power (watts): 40W
• Mounting Type: Through Hole
• Voltage - Input: 9 ~ 36V
• Package / Case: 8-DIP Module
• 1st Output: 12 VDC @ 3.33A
• Size / Dimension: 2.00" L x 2.00" W x 0.40" H (50.8mm x 50.8mm x 10.2mm)
• Power (watts) - Rated: 40W
• Operating Temperature: -40°C ~ 95°C
• Efficiency: 87%
• Approvals: cUL, UL
• Brand/series: RP40-SG Series
• Configuration: Encapsulated
• Operation: Linear
• Power, Output: 40 W
• Primary Type: DC-DC
• Special Features: Efficiency to 86%; Over Current and Over voltage protection
• Voltage, Input: 9-36 VDC
• Voltage, Output: 12 VDC
• 4: 1 Wide Input Voltage Range
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: 30000886; 945-1281

P-96
POWERLINE
DC/DC-Converter
Notes :
Package Style and Pinning (mm)
1. For the single output: Maximum output deviation is 10% inclusive of remote sense and trim. If remote sense is not being used, the +sense should be connec-
2. BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C
MIL-HDBK-217F Notice 2 @ Ta=25°C, full load (GroundBenign, controlled environment).
3. Simulated source impedance of 12µH. 12µH inductor in series with +Vin.
4. Maximum value at nominal input voltage and no load.
5. Typical value at nominal input voltage and full load.
6. Test by minimum Vin and constant resistive load.
7. The ON/OFF control function. There are positive logic (standard) and negative logic (option). The pin voltage is referenced to Vin- input
8. Heat sink is optional and P/N: 7G-0026-C. Powerline DC/DC Converters can be ordered with pre-mounted heatsinks including antivibration fixing clips
9. The dual output required a minimum loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices,
10. Load regulation for dual output : Min load to 100% load balanced on all outputs.
11.Cross regulation for dual output : asymmetrical load 25% <> 100% FL.
12..The RP40-GW series required external filter to meets EN55022 class A.
13.See application notes for Class B common mode filter suggestion
ted to its corresponding +OUTPUT and likewise the -sense should be connected to its corresponding –OUTPUT.
To order negative logic ON/OFF control add the suffix-N (Ex: RP40-4805SGW-N).
(add suffix -HC). See Application Notes for heatsink details.
however they may not meet all listed specification.
REV: 1/2010
External Output Trimming
Output can be externally trimmed by using the method
shown below. ( ) for dual output tri.
See Application Notes for more details.
RP40-S_DGW
Series
Pin Connections
Pin #
1
2
3
4
5
6
7
8
Pin Pitch Tolerance ±0.25 mm
+SENSE (Note 2)
-SENSE (Note 1)
Single
+Vout
CTRL
-Vout
TRIM
+Vin
-Vin
www.recom-electronic.com
+Vout
CTRL
-Vout
TRIM
Dual
+Vin
Com
Com
-Vin