VWRBS2-D48-S15-SIP CUI Inc, VWRBS2-D48-S15-SIP Datasheet - Page 3
![CONVERTER DC/DC 15V OUT 2W](/photos/8/64/86445/vwrbs2-d48-s15-sip_sml.jpg)
VWRBS2-D48-S15-SIP
Manufacturer Part Number
VWRBS2-D48-S15-SIP
Description
CONVERTER DC/DC 15V OUT 2W
Manufacturer
CUI Inc
Series
V-Infinity VWRBS2-SIPr
Type
Isolatedr
Datasheet
1.VWRBS2-D48-S15-SIP.pdf
(3 pages)
Specifications of VWRBS2-D48-S15-SIP
Output
15V
Number Of Outputs
1
Power (watts)
2W
Mounting Type
Through Hole
Voltage - Input
36 ~ 72V
Package / Case
8-SIP Module (7 Leads)
1st Output
15 VDC @ 133mA
Size / Dimension
0.87" L x 0.37" W x 0.47" H (22mm x 9.5mm x 12mm)
Power (watts) - Rated
2W
Operating Temperature
-40°C ~ 85°C
Efficiency
79%
Approvals
UL
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-
4th Output
-
Other names
102-1520
PART NUMBER: VWRBS2
Application Notes:
- All of the VWRBS2-SIP Series have been tested
-
R= Vc - Vd - 0.65V
Remote on/off control (see figure 1)
ON: When control pin (CTRL pin 3) open or Ic
OFF: With a 3-10mA input current (Ic) to pin 3, output will be disabled. Under no conditions
should input current (Ic) exceed 20mA. The Value of R in Figure 1 can be derived as follows:
example 1 : Logic circuit — Apply 5V TTL logic signal on Vc to disable output
example 2 : Short Vin to Vc — Apply 12V on Vc to disable output
according to the following recommended testing
circuit before leaving the factory. This series should
be tested under load(Figure 1). If you want to further
decrease the input/output ripple, you can increase
capacitance properly or choose capacitors with
low ESR. However, the capacitance should not be too
high(Table 2).
20050 SW 112
Vout(VDC)
Single
3.3
12
15
24
5
9
R=
R=
Ic
External Capacitor Table
5V - 0.7V - 0.65V
12V - 0.7V - 0.65V
Cout(uF)
2200
1000
680
560
470
820
.005A
.005A
Temperature Derating Graph
th
Operating Temp.(
Ave. Tualatin, Oregon 97062
Table 2
Vout(VDC)
Vc= Voltage at control input
Vd= Diode (D1) voltage drop (.7V voltage drop typical )
Ic= Input Current (5mA recommended disable current)
Dual
±12
±15
±5
±9
-
-
= 730 Ω
= 2130 Ω
C
)
Cout(uF)
±560
±470
±330
±270
-
-
Choose 720Ω resistor
Choose 2K Ω resistor
Cs (uF)
<
47
47
47
47
0.5mA, converter will have normal output.
-
-
phone
phone 503.612.2300 fax
DESCRIPTION: dc-dc converter
- Input current
- Output Load
- NC Terminals
Nominal input voltage range. The input
current of the power supply must be sufficient
to the startup current (Ip) of the DC/DC module
(Figure 2)
In order to ensure the product operates
efficiently and reliably, make sure the specified range
of input voltage is not exceeded.
No parallel connection or plug and play.
Unless otherwise specified, NC terminals of all series
are used for converter's interior circuit
connection, and are not allowed connection of any
external circuit.;
fax 503.612.2383
Input Voltage (V)
Ip
Input Voltage
Range
www.v-infinity.com
rev.
page
date
09/2009
3 of 3