LTM4602HVIV#PBF Linear Technology, LTM4602HVIV#PBF Datasheet - Page 10
![IC DC/DC UMODULE 6A 104-LGA](/photos/8/69/86988/104-lga_05-08-1800_sml.jpg)
LTM4602HVIV#PBF
Manufacturer Part Number
LTM4602HVIV#PBF
Description
IC DC/DC UMODULE 6A 104-LGA
Manufacturer
Linear Technology
Series
µModuler
Type
Point of Load (POL) Non-Isolatedr
Datasheet
1.LTM4602HVEVPBF.pdf
(24 pages)
Specifications of LTM4602HVIV#PBF
Design Resources
LTM4602HV Spice Model
Output
0.6 ~ 5 V
Number Of Outputs
1
Power (watts)
30W
Mounting Type
Surface Mount
Voltage - Input
4.5 ~ 28 V
Package / Case
104-LGA
1st Output
0.6 ~ 5 VDC @ 6A
Size / Dimension
0.59" L x 0.59" W x 0.11" H (15mm x 15mm x 2.8mm)
Power (watts) - Rated
30W
Operating Temperature
-40°C ~ 85°C
Efficiency
92%
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIO S I FOR ATIO
LTM4602HV
in the PCB layout to minimize the trace inductance and
high frequency AC noise.
Output Capacitors
The LTM4602HV is designed for low output voltage ripple.
The bulk output capacitor C
effective series resistance (ESR) to meet the output voltage
ripple and transient requirements. C
tantalum capacitor, low ESR polymer capacitor or ceramic
capacitor (X5R or X7R). The typical capacitance is 200µF
if all ceramic output capacitors are used. The internally
optimized loop compensation provides suffi cient stability
margin for all ceramic capacitors applications. Additional
output fi ltering may be required by the system designer,
if further reduction of output ripple or dynamic transient
spike is required. Refer to Table 2 for an output capaci-
tance matrix for each output voltage Droop, peak to peak
deviation and recovery time during a 3A/µs transient with
a specifi c output capacitance.
Fault Conditions: Current Limit and Over current
Foldback
The LTM4602HV has a current mode controller, which
inherently limits the cycle-by-cycle inductor current not
only in steady state operation, but also in transient.
To further limit current in the event of an over load condi-
tion, the LTM4602HV provides foldback current limiting.
If the output voltage falls by more than 50%, then the
maximum output current is progressively lowered to about
one sixth of its full current limit value.
10
U
U
OUT
is chosen with low enough
W
OUT
can be low ESR
U
Soft-Start and Latchoff with the RUN/SS pin
The RUN/SS pin provides a means to shut down the
LTM4602HV as well as a timer for soft-start and over-
current latchoff. Pulling the RUN/SS pin below 0.8V puts
the LTM4602HV into a low quiescent current shutdown
(I
current source to charge up the timing capacitor C
Inside LTM4602HV, there is an internal 1000pF capaci-
tor from RUN/SS pin to ground. If RUN/SS pin has an
external capacitor C
starting is about:
When the voltage on RUN/SS pin reaches 1.5V, the
LTM4602HV internal switches are operating with a clamp-
ing of the maximum output inductor current limited by the
RUN/SS pin total soft-start capacitance. As the RUN/SS pin
voltage rises to 3V, the soft-start clamping of the inductor
current is released.
V
There are restrictions in the maximum V
down ratio that can be achieved for a given input voltage.
These constraints are shown in the Typical Performance
Characteristics curves labeled “V
Ratio”. Note that additional thermal de-rating may apply.
See the Thermal Considerations and Output Current De-
Rating sections of this data sheet.
IN
Q
t
≤ 75µA). Releasing the pin allows an internal 1.2µA
DELAY
to V
OUT
=
Stepdown Ratios
1 2
1 5
.
.
µ
V
A
•(
SS_EXT
C
SS EXT
_
to ground, the delay before
+
1000
IN
to V
pF
)
IN
OUT
to V
Stepdown
OUT
4602hvf
step
SS
.