LTM4606EV#PBF Linear Technology, LTM4606EV#PBF Datasheet - Page 7
![IC DC/DC UMODULE 6A 133-LGA](/photos/8/69/86991/ltm4606ev_pbf_sml.jpg)
LTM4606EV#PBF
Manufacturer Part Number
LTM4606EV#PBF
Description
IC DC/DC UMODULE 6A 133-LGA
Manufacturer
Linear Technology
Series
µModuler
Type
Point of Load (POL) Non-Isolatedr
Datasheet
1.LTM4606EVPBF.pdf
(28 pages)
Specifications of LTM4606EV#PBF
Design Resources
LTM4606 Spice Model
Output
0.6 ~ 5 V
Number Of Outputs
1
Power (watts)
30W
Mounting Type
Surface Mount
Voltage - Input
4.5 ~ 28 V
Package / Case
133-LGA
1st Output
0.6 ~ 5 VDC @ 6A
Size / Dimension
0.59" L x 0.59" W x 0.11" H (15mm x 15mm x 2.8mm)
Power (watts) - Rated
30W
Operating Temperature
-40°C ~ 125°C
Efficiency
93%
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
pin FuncTions
V
tween these pins and PGND pins. Recommend placing
input decoupling capacitance directly between V
and PGND pins.
V
between these pins and PGND pins. Recommend placing
output decoupling capacitance directly between these pins
and PGND pins (see figure below).
PGND (Bank 2): Power Ground Pins for Both Input and
Output Returns.
V
between V
and reduce the input ripple further.
DRV
nect to INTV
They can be biased up to 6V from an external supply with
about 50mA capability, or an external circuit as shown in
Figure 18. This improves efficiency at the higher input
voltages by reducing power dissipation in the modules.
INTV
the 5V internal regulator.
PLLIN (Pin A8): External Clock Synchronization Input to
the Phase Detector. This pin is internally terminated to
SGND with a 50k resistor. Apply a clock with high level
above 2V and below INTV
mation section.
FCB (Pin M12): Forced Continuous Input. Connect this pin
to SGND to force continuous synchronization operation at
low load, to INTV
tion at low load or to a resistive divider from a secondary
output when using a secondary winding.
TRACK/SS (Pin A9): Output Voltage Tracking and Soft-Start
Pin. When the module is configured as a master output,
then a soft-start capacitor is placed on this pin to ground
to control the master ramp rate. A soft-start capacitor can
be used for soft-start turn-on as a standalone regulator.
Slave operation is performed by putting a resistor divider
from the master output to ground, and connecting the
center point of the divider to this pin. See the Applications
Information section.
IN
OUT
D
(Pins B7, C7): Top FET Drain Pins. Add more capacitors
(Bank 1): Power Input Pins. Apply input voltage be-
CC
CC
(Bank 3): Power Output Pins. Apply output load
(Pins C10, E11, E12): These pins normally con-
(Pin A7): This pin is for additional decoupling of
D
CC
and ground to handle the input RMS current
for powering the internal MOSFET drivers.
CC
to enable discontinuous mode opera-
CC
. See the Applications Infor-
IN
pins
MPGM (Pins A12, B11): Programmable Margining Input.
A resistor from these pins to ground sets a current that
is equal to 1.18V/R. This current multiplied by 10kW will
equal a value in millivolts that is a percentage of the 0.6V
reference voltage. See the Applications Information section.
To parallel LTM4606s, each requires an individual MPGM
resistor. Do not tie MPGM pins together.
f
continuous conducting mode at light load. An external
resistor can be placed from this pin to ground to increase
frequency. This pin can be decoupled with a 1000pF
capacitor. See the Applications Information section for
frequency adjustment.
V
Internally, this pin is connected to V
sion resistor. Different output voltages can be programmed
with an additional resistor between the V
See the Applications Information section.
MARG0 (Pin C12): LSB Logic Input for the Margining
Function. Together with the MARG1 pin, the MARG0 pin
will determine if a margin high, margin low, or no margin
state is applied. The pin has an internal pulldown resistor
of 50k. See the Applications Information section.
MARG1 (Pins C11, D12): MSB Logic Input for the Margin-
ing Function. Together with the MARG0 pin, the MARG1
pins will determine if a margin high, margin low, or no
margin state is applied. The pins have an internal pull-down
resistor of 50k. See the Applications Information section.
SGND (Pins D9, H12): Signal Ground Pins. These pins
connect to PGND at output capacitor point.
COMP (Pins A11, D11): Current Control Threshold and
Error Amplifier Compensation Point. The current com-
parator threshold increases with this control voltage. The
voltage ranges from 0V to 2.4V with 0.7V corresponding
to zero sense voltage (zero current).
PGOOD (Pin G12): Output Voltage Power Good Indicator.
Open-drain logic output that is pulled to ground when the
output voltage is not within ±10% of the regulation point,
after a 25µs power bad mask timer expires.
SET
FB
(Pin F12): The Negative Input of the Error Amplifier.
(Pin B12): Frequency set internally to 800kHz in
OUT
with a 60.4k preci-
LTM4606
FB
and SGND pins.
4606fb
7