IPM24S0B0S03FA Delta Electronics, IPM24S0B0S03FA Datasheet

Page 1

... The Delphi Series IPM24S0B0 non-isolated, fully integrated Point-of-Load (POL) power modules, are the latest offerings from a world leader in power systems technology and manufacturing -- Delta Electronics, Inc. This product family provides output current or 20W of output power in an industry standard, compact, IC-like, molded package highly integrated and does not require external components to provide the point-of-load function. A copper pad on the back of the module ...

Page 2

TECHNICAL SPECIFICATIONS T = 25°C, airflow rate = 300 LFM 24Vdc, nominal Vout unless otherwise noted PARAMETER ABSOLUTE MAXIMUM RATINGS Input Voltage (Continuous) Operating Temperature Storage Temperature INPUT CHARACTERISTICS Operating Input Voltage Input Under-Voltage Lockout Turn-On ...

Page 3

ELECTRICAL CHARACTERISTICS CURVES 89.0 84.0 79.0 74.0 69.0 64.0 59.0 54.0 0.0 0.5 1.0 1.5 2.0 Iout (A) Figure 1: Converter efficiency vs. output current (3.30V output voltage) 92.0 88.0 84.0 80.0 76.0 72.0 68.0 64.0 60.0 0.0 0.5 1.0 ...

Page 4

ELECTRICAL CHARACTERISTICS CURVES Figure 7: Output ripple & noise at 12Vin, 4.0V/3A out Figure 9: Output ripple & noise at 12Vin, 5.0V/3A out Figure 11: Output ripple & noise at 12Vin, 6.5V/3A out DS_IPM24S0B0_03202007 Figure 8: Output ripple & noise ...

Page 5

ELECTRICAL CHARACTERISTICS CURVES Figure 13: Power on waveform at 12vin, 3.3V/3A out with application of Vin Figure 15: Power off waveform at 12vin, 3.3V/3A out with application of Vin Figure 17: Remote turn on delay time at 24vin, 6.5V/3A out ...

Page 6

ELECTRICAL CHARACTERISTICS CURVES Figure 19: Turn on delay at 24vin, 3.3V/3A out with application of Vin Figure 21: Typical transient response to step load change at 0.5A/µS from 100% to 50% of Io, max at 12Vin, 6.5V out (measurement with ...

Page 7

TEST CONFIGURATIONS TO OSCILLOSCOPE L 2 100uF BATTERY Electrolytic Note: Input reflected-ripple current is measured with a simulated source inductance. measured at the input of the module. Figure 23: Input reflected-ripple current test setup COPPER STRIP Vo 220uF 1uF SCOPE ...

Page 8

DESIGN CONSIDERATIONS Remote On/Off The IPM series power modules have an On/Off control pin for output voltage remote On/Off operation. The On/Off pin is an open collector/drain logic input signal that is referenced to ground. When On/Off control pin is ...

Page 9

FEATURES DESCRIPTIONS (CON.) Figure 28: Trim up Circuit configuration for programming output voltage using an external resistor Vout Rtrim Trim GND Figure 29: Trim down Circuit configuration for programming output voltage using an external resistor Figure 30: Circuit configuration for ...

Page 10

THERMAL CONSIDERATIONS Thermal management is an important part of the system design. To ensure proper, reliable operation, sufficient cooling of the power module is needed over the entire temperature range of the module. Convection cooling is usually the dominant mode ...

Page 11

THERMAL CURVES Figure 32: Temperature measurement location * The allowed maximum hot spot temperature is defined at 125 IPM24S (Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin=24V, Vout = 6.5V (Either Orientation) Output Current(A) 3 Natural Convection ...

Page 12

PICK AND PLACE LOCATION All dimensions are in millimeters (inches) LEAD FREE PROCESS RECOMMEND TEMP. PROFILE Te Te mp. mp Peak Tem p. 240 ~ 245 Peak Tem p. 240 ~ 245 217 217 ...

Page 13

Mechanical Drawing SMD PACKAGE RECOMMEND PWB PAD LAYOUT Note : The copper pad is recommended to connec ote: All dimension are in millimeters (inches) standard dimension tolerance is DS_IPM24S0B0_03202007 SIP PACKAGE 1 ...

Page 14

PART NUMBERING SYSTEM IPM 24 S Product Number of Input Voltage Family Outputs Integrated POL 11V ~ 36V S - Single Module MODEL LIST Model Name Input Voltage IPM24S0A0S/R03FA 8V ~ 36V IPM24S0B0S/R03FA 11V ~ 36V Model Name Input Voltage ...