MPDTY115S Murata Electronics North America, MPDTY115S Datasheet
![CONV DC/DC 12W 2.0VOUT 6A SMT](/photos/8/74/87410/mpdty115s_sml.jpg)
MPDTY115S
Specifications of MPDTY115S
Available stocks
Related parts for MPDTY115S
MPDTY115S Summary of contents
Page 1
DC-DC Converter Specification 1 . Application This specification applies to DC-DC Converter MPD6D12*S(*:2∼8) for telecommunication / data-communication equipment. For any other application, please contact us before using this product Customer Reference Customer Spec. Number Customer Part Number 3 ...
Page 2
Appearance, Dimensions Objective Products MPD6D12*S (*:2,3,4,6,7,8) Dot Mark (where close to 1pin 42.4+/-0.5 45.0+/-0.6 Marking Part Number MPD6D12_S Murata CM Mark Lot Number ...
Page 3
Pin Number and Function Pin No Pin Symbol 1,2, 16,17, NCo 18,19, 33,34 3 ALM -Vin 10 -Vin 11 -Vin 13 +Vin 14 +Vin 15 +Vin 20 +Vout 21 ...
Page 4
Environmental Conditions 7 .1. Operating Temperature Range 7 .2. Operating Humidity Range 7 .3. Storage Temperature Range 7 .4. Storage Humidity Range 8. Absolute Rating Item Minimum Input Voltage Maximum Input Voltage ALM Applied Voltage RC Applied Voltage PO ...
Page 5
Specific Characteristics (Ta= -40 to +85°C with power derated.) Models Items Nominal Output Voltage Output Voltage Regulation Vin =36 to 75V Output current range = 0 to 100% Nominal Output Current Output Current-limit Min Inception Over Voltage ...
Page 6
Typical Power derating of MPD6D122S to MPD6D128S MPD6D122S (Vo=1.2V) Vin=36to75V 0.2m/s(40LFM) 4 0m/s(0LFM - Ambient Temperature [℃] MPD6D124S (Vo=1.8V) Vin=36to75V 12 11A 0.2m/s(40LFM) 4 0m/s(0LFM -40 ...
Page 7
Operation Information 9.2.1. Reset Condition In order to reset all function , the input voltage (Vin) is set under 5V for 1s. min. Reset Condition 9.2.2. Over Voltage Protection (OVP) The Isolated DC-DC Converter become into latch-up mode after ...
Page 8
Remote On/Off Control The connection pin controls an Isolated DC-DC Converter to turn on/off. While the Isolated DC-DC Converter is halted under the remote control, alarm function does not operate;refer to Alarm Output. Start : RC ...
Page 9
Reliability 9.3.1. Humidity Test Parts are subjected to a temperature 40°C±2°C with 90∼95% for 100 hours. Return the parts to room temperature (25°C) for 4 hours and measure. The initial values under item 9-1 should be met. (JIS-C-0022) 9.3.2. ...
Page 10
Measure Construction 10.1. Standard Test Circuit A Ein V 10.1.1. Output Ripple & Noise +IN Ein -IN IN Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to ...
Page 11
Radiated EMI Noise Measurement Cramper 10.1.3. Conduction Noise Measurement LISN KNW-407 Kyoritsu Corporation Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our products in ...
Page 12
Packaging Information 11.1. Tray Dimensions DC-DC Converters are put in the trays 56.0 B-B' Cross Section Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to ...
Page 13
Maximum Pieces per a Tray. 12pcs/tray(except less than 12) 11.3. Package Corrugated cardboard box contains trays with products. Tray is heaped with alternately opposite direction to prevent products from contacting against the bottoms of trays. Numerals in parentheses are ...
Page 14
Notice 12.1. Soldering 12.1.1. Flux Please solder this product with Rosin Flux, which contains of 0.2wt%. or less chlorine. Please do not use high activity acid flux or water soluble flux because they may erode metal or glass portion ...
Page 15
Storage 12.3.1. Please store the products in room where the temperature/humidity is stable and direct sunlight cannot come in ,and use the products within 6 months after delivery. Avoid damp heated places or such places where there are large ...
Page 16
Transportation If you transport the products, please wrap-up in addition to the standard package. Otherwise mechanical vibrations or mechanical shocks, may damage the package and please direct transporters to handle with care. If you transport the products to overseas ...