APTH012A0X3-SRZ Lineage Power, APTH012A0X3-SRZ Datasheet - Page 13
![DC-DC 0.6-3.63V @ 12A SMD](/photos/8/75/87506/apth012a0x3-srz_sml.jpg)
APTH012A0X3-SRZ
Manufacturer Part Number
APTH012A0X3-SRZ
Description
DC-DC 0.6-3.63V @ 12A SMD
Manufacturer
Lineage Power
Series
Micro TLynx™r
Type
Point of Load (POL) Non-Isolated with Remote On/Offr
Datasheet
1.APXH012A0X3-SRZ.pdf
(23 pages)
Specifications of APTH012A0X3-SRZ
Output
0.6 ~ 3.63V
Number Of Outputs
1
Power (watts)
44W
Mounting Type
Surface Mount
Voltage - Input
2.4 ~ 5.5V
Package / Case
10-SMD Module
1st Output
0.6 ~ 3.63 VDC @ 12A
Size / Dimension
0.80" L x 0.45" W x 0.33" H (20.3mm x 11.4mm x 8.5mm)
Power (watts) - Rated
44W
Operating Temperature
-40°C ~ 85°C
Efficiency
94%
Approvals
CSA, EN, UL, VDE
Product
Non-Isolated / POL
Input Voltage Range
2.4 V to 5.5 V
Output Voltage (channel 1)
0.6 V to 3.63 V
Output Current (channel 1)
12 A
Package / Case Size
20.3 mm x 11.4 mm x 8.5 mm
Output Type
Non-Isolated
Output Voltage
0.6 V to 3.63 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
555-1128-2
Data Sheet
April 7, 2011
pulled low, Q2 is turned off and the internal PWM
Enable signal is pulled high through the 23.7K pull-up
resistor and the module is OFF.
Figure 38. Circuit configuration for using positive
On/Off logic.
For negative logic On/Off modules, the circuit
configuration is shown in Fig. 39. The On/Off pin should
be pulled high with an external pull-up resistor
(suggested value for the 2.4V to 5.5Vin range is
3Kohms). When transistor Q1 is in the OFF state, the
On/Off pin is pulled high and the module is OFF. The
On/Off threshold for logic High on the On/Off pin
depends on the input voltage and its minimum value is
V
pulling the On/Off pin low.
Figure 39. Circuit configuration for using negative
On/Off logic.
Overcurrent Protection
To provide protection in a fault (output overload)
condition, the unit is equipped with internal
current-limiting circuitry and can endure current limiting
continuously. At the point of current-limit inception, the
LINEAGE
ON/OFF
IN
VIN+
ON/OFF
VIN+
GND
Q1
GND
– 1.6V. To turn the module ON, Q1 is turned ON
Rpullup
V
Q1
POWER
I
ON/OFF
I
V
ON/OFF
ON/OFF
ON/OFF
+
_
+
_
20K
MODULE
20K
20K
MODULE
Q2
R2
2.4 – 5.5Vdc input; 0.6Vdc to 3.63Vdc output; 12A output current
470
PWM Enable
PWM Enable
23.7K
60.4K
Micro TLynx
unit enters hiccup mode. The unit operates normally
once the output current is brought back into its specified
range.
Overtemperature Protection
To provide protection in a fault condition, the unit is
equipped with a thermal shutdown circuit. The unit will
shutdown if the overtemperature threshold of 130
exceeded at the thermal reference point T
thermal shutdown is not intended as a guarantee that
the unit will survive temperatures beyond its rating.
Once the unit goes into thermal shutdown it will then
wait to cool before attempting to restart.
Input Undervoltage Lockout
At input voltages below the input undervoltage lockout
limit, the module operation is disabled. The module will
begin to operate at an input voltage above the
undervoltage lockout turn-on threshold.
Output Voltage Programming
The output voltage of the Micro TLynx
programmed to any voltage from 0.6dc to 3.63Vdc by
connecting a resistor between the Trim+ and GND pins
of the module. Certain restrictions apply on the output
voltage set point depending on the input voltage. These
are shown in the Output Voltage vs. Input Voltage Set
Point Area plot in Fig. 40. The Upper Limit curve shows
that the entire output voltage range is available with the
maximum input voltage of 5.5V. The Lower Limit curve
shows that for output voltages of 1.8V and higher, the
input voltage needs to be larger than the minimum of
2.4V.
Figure 40. Output Voltage vs. Input Voltage Set
Point Area plot showing limits where the output
voltage can be set for different input voltages.
pins, the output of the module will be 0.6Vdc. To
calculate the value of the trim resistor, Rtrim for a
desired output voltage, use the following equation:
Without an external resistor between Trim+ and GND
6
5
4
3
2
1
0
TM
0.5
: Non-isolated DC-DC Power Modules:
1
1.5
Upper Limit
Output Voltage (V)
2
2.5
Lower Limit
TM
3
module can be
ref
. The
3.5
o
C is
4
13