750-00004 Parallax Inc, 750-00004 Datasheet - Page 10

• Manufacturer Part Number: 750-00004
• Description: POWER SUPPLY 24VDC 600MA
• Manufacturer: Parallax Inc

Specifications of 750-00004

• Form: Wall Mount (2 Prong)
• Voltage - Output Per Connector: 24VDC
• Current - Output: 600mA
• Polarization: Positive Center
• Cord Plug: 2.1mm I.D. x 5.5mm O.D. x 12mm Female
• Voltage - Input: 120VAC
• Power - Output: 14W
• Transformer Type: Linear, Unregulated
• Product: Microcontroller Accessories
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Efficiency: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Contains lead / RoHS non-compliant

The A/D Converter is configured by sending it a control byte. The control byte is made up of
configuration bits
The entire process of configuring the ADC and retrieving the conversion results can be accomplished with
just a few PBASIC commands. The following program has been written to configure the ADC for 0-5 VDC
and read the analog voltage present at Ain 2.
'{$STAMP
'{$PBASIC 2.5}
'
ClkAdc
CsAdc
AoutAdc
AinAdc
adResult
Main:
The LOW CsAdc command sets the Chip Select input of the ADC low, thereby enabling communications
on the ADC. The SHIFTOUT command sends the configuration to the ADC. The "HIGH CSadc" signals
the completion of the configuration and the start of the data conversion. The data conversion process
requires at least 9.09 uSec to complete. Since the inter-instruction time for all Stamps is higher than this,
no additional delay is required. The next "LOW CDadc" command enables communication for the reply.
The SHIFTIN command retrieves the converted data. The following "HIGH CSadc" command ends the
communications. The DEBUG command formats and displays the data for our viewing ease.
4
select bits is a subtle hint. Analog input channels 1:4 are mapped to A/D converter channels 7:4. It was decided to limit the number of analog input
channels to accommodate the number of connections available in this small enclosure.
Parallax, Inc. • Stamp PLC (#30064) • Version 1.8 • 12/29/2003
You may have noticed that the MAX1270 is an 8 channel A/D converter, (yet only 4 channels are employed). The fact that there are three channel
DO
LOOP
LOW CsAdc
SHIFTOUT AoutAdc, ClkAdc, MSBFIRST, [%11100000]
HIGH CsAdc
LOW CsAdc
SHIFTIN AinAdc, ClkAdc, MSBPRE, [adResult\12]
HIGH CsAdc
DEBUG "
BS2}
Figure 11: A/D Converter
ADC2:", SDEC adResult, CR
4
Channel
. The meaning of each configuration bit is defined by the chart in Figure 10.
Analog
4
3
2
1
Start
PIN
PIN
PIN
PIN
VAR
Bit7
1
bit table
Figure 10: A/D Converter control byte legend
SEL2
Bit6
1
W
0
3
4
5
Word
0
0
1
1
SEL1
Bit5
W
X
0
1
0
1
SEL0
Bit4
X
' A/D clock
' Chip Select for ADC
' A/D Data out
' A/D Data in
Y
0
0
1
1
Figure 12: A/D Converter bit table
RNG
Bit3
Y
Z
0
1
0
1
Bit2
BIP
Z
'Ch2 0-5 VDC
-10 VDC to +10 VDC
-5 VDC to +5 VDC
0 VDC to +10VDC
0 VDC to +5 VDC
Bit1
PD1
0
Range
PD0
Bit0
0
Page
10