AS-ISP-EPM Phyton Inc, AS-ISP-EPM Datasheet

no-image

AS-ISP-EPM

Manufacturer Part Number
AS-ISP-EPM
Description
ADPT CHIPPROG-ISP BH14/BH10 SPEC
Manufacturer
Phyton Inc
Datasheet

Specifications of AS-ISP-EPM

Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Adapters - Phyton, Inc.
http://phyton.com/downloads/adp/adapters.asp?Adap_ID=380
Quick Links
Help Desk
Downloads
All Programmers
Device Search
Tools Catalogs
Your Account
Products
Development Tools
Device programmers
Custom made tools
OEM tools
ARM
8051
All Models
Universal
In-System
Gang
Adapters
Other
Shopping Cart
Home
Items: 0
Total: $0.00
Products
AS-ISP-EPM
Connections to the target devices:
ChipProg-ISP BH14/BH10 specialized adapter for in system programming of Altera EPM300A PLD
family .
AS-ISP-EPM connection for the EPM300A devices
Supported Devices:
Click the programmer model below to get an appropriate list of the devices supported by the adapter:
Recommended connection:
Table of connections of the adapter output socket to the
device pins:
Device Programmers and Development Tools for Microcontrollers
AS-ISP-EPM connection for the EPM300A devices
ChipProg-ISP
E-Shop
Support
Contact
Description:
ChipProg-ISP BH14/BH10 specialized adapter for in
system programming of Altera EPM300A PLD family .
Supported Devices:
Click the device programmer model below to get an
appropriate list of the devices supported by this
programmer with this adapter:
Adapter wiring diagram
Powering the target device:
There are two alternative options for powering the
targets:
1. The target gets power from the programmer (Vdd).
This is possible only if the target does not consume too
much energy. A capacity of the target power circuitry
should not exceed 50 uF.
2. The target gets power from a built-in or external
power supply. In this case the power output from the
programmer should not be connected with the target.
The target system should be tolerant to applying logical
signals with the voltage levels exceeding the voltages
on the target.
NOTE! It is strictly prohibited to power the target from
both the programmer and built-in or external power
supply simultaneously.
Isolating resistors:
Purpose of the R1..R4 resistors is to isolate the
programmed chip from rest of target system.
Recommended value of resistors R1..R4 is 2k or more.
You can also use jumpers instead of the resistors.
ISP characteristics:
1. Programmer's output capability:
1.1 Vcc - 80 mA;
1.2 Vpp - 50 mA;
1.3 logical pins - 5 mA.
2. The cable length should be less then one foot.
/Start is the input signal, active state is 0. This signal
works as the Start button on the programmer.
/Error, /Good, /Busy are output logical signals, active
state is 0. They indicate the programmer status and
work as the corresponding LEDs on the programmer
case.
ChipProg-ISP
News
Page 1 of 2
Site Map
8/23/2010

Related parts for AS-ISP-EPM

AS-ISP-EPM Summary of contents

Page 1

... Gang Adapters • AS-ISP-EPM connection for the EPM300A devices Custom made tools OEM tools AS-ISP-EPM connection for the EPM300A devices Supported Devices: Click the programmer model below to get an appropriate list of the devices supported by the adapter: • ChipProg-ISP Recommended connection: Table of connections of the adapter output socket to the device pins: http://phyton ...

Page 2

... Adapter Output connector, BH- 6,7 Adapter Connection Table: From Programmer Output Connector Copyright © 2007-2010 Phyton, Inc. http://phyton.com/downloads/adp/adapters.asp?Adap_ID=380 Target Device EPM3xxx TCK GND TDO VCC TMS - TDI GND Status and To the Target Control Device Signals from Programmer /Start /Error /Good /Busy Phone: 718-259-3191 • ...

Related keywords