CY3276 Cypress Semiconductor Corp, CY3276 Datasheet - Page 13
![DEV PROG POWERLINE HIGH EZCOLOR](/photos/9/6/90661/cy3276_sml.jpg)
CY3276
Manufacturer Part Number
CY3276
Description
DEV PROG POWERLINE HIGH EZCOLOR
Manufacturer
Cypress Semiconductor Corp
Type
Other Power Managementr
Datasheet
1.CY3276.pdf
(36 pages)
Specifications of CY3276
Mfg Application Notes
Powerline Comm Brd Design AppNote
Main Purpose
Interface, Transceiver, Powerline Communication
Embedded
No
Utilized Ic / Part
CY8CLED16P01
Primary Attributes
2400bps Data Transfer Over High Voltage Power Lines
Secondary Attributes
User Configurable LEDs
Board Size
127 mm x 101.6 mm
Interface Type
RS-232, Ethernet, I2C, ISSP
Maximum Operating Temperature
+ 40 C
Operating Supply Voltage
110 V to 240 V
Product
Power Management Development Tools
Dimensions
127 mm x 101.6 mm
Silicon Manufacturer
Cypress
Silicon Core Number
CY8CLED16P01
Kit Application Type
Communication & Networking
For Use With/related Products
CY8CLED16P01
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
428-3004
CY3276 Cypress High Voltage Programmable PLC Development Kit Guide, Doc. # 001-55116 Rev. *B
Table 2-4. Headers and Jumpers
CY8CLED16P01-OCD
PWR LED[DS1]
TX LED[DS3]
RX LED[DS2]
BIU LED[DS4]
TP1, TP2, TP3, TP4
S2
J8
LED1-LED4
JP1 (PWR)
JP5 (Reset)
JP4 (I2C-SDA)
JP3 (I2C-SCL)
P40-P46
P47
P01,P02,P04
P07
P21
P23
P25
P26
P17
P15
P16, P12
P30,P31,P32,P33,P34,P35
P36,P37
Headers and Jumpers
This is the Cypress Powerline transceiver chip. It is a 100-pin OCD device
This is a blue LED that glows when the board is powered on
This is a green LED that can be used to indicate when the board is transmit-
ting packets on to the powerline
This is a red LED that can be used to indicate when the signal is received
over the powerline on to the board
This is a yellow LED that can be used to indicate when the transmit fre-
quency band is in use
Grounded test points to facilitate probing/debugging
Reset switch for resetting the CY8CLED16P01-OCD chip
2-pin header for connecting to Vcc and Gnd
Headers connected to general purpose configurable LEDs
Connect this jumper to power an external board. Once this jumper has been
connected, power for the external board can be derived from the V and G
connectors on the I2C header (J15). The CY3276 board can provide a max-
imum of 50mA at 5V to an external board through the V and G pins on the
I2C header(J15).
The jumper is for enabling the reset of the PLC chip through an external
board. Once this jumper has been connected, the external board reset can
be connected to the R pin on the I2C header (J15).
This is a pull up jumper. While communicating through I2C(J15), one side
has to pull up the line. When the jumper is connected, the SDA line will get
pulled high. This needs to be done when the user wants the I2C link to be
pulled up by CY3276 board.
This jumper does not need to be placed if the USB-I2C bridge is used for
communication to the host.
This is a pull up jumper. While communicating through I2C(J15), one side
has to pull up the line. When the jumper is connected, the SCL line will get
pulled high. This needs to be done when the user wants the I2C link to be
pulled up by CY3276 board.
This jumper does not need to be placed if the USB-I2C bridge is used for
communication to the host.
Port pins connected to the LCD card
Free port pin
Port pins connected to LED card used for current sensing feedback for
accurate color control
Free port pin
Port pin connected to the yellow LED for BIU
Port pin connected to the red LED for Rx
Port pin connected to the green LED for Tx
Free port pin
Port pin connect to SCL for I2C
Port pin connect to SDA for I2C
Free port pins
Port pins connected to LED card
Free port pins
Description
PLC Development Board
13
[+] Feedback