DS16EV51-AEVKH National Semiconductor, DS16EV51-AEVKH Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
DS16EV51-AEVKH
Manufacturer Part Number
DS16EV51-AEVKH
Description
BOARD EVAL FOR DS16EV5110A
Manufacturer
National Semiconductor
Specifications of DS16EV51-AEVKH
Main Purpose
Video, Cable Extender
Utilized Ic / Part
DS16EV5110A
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Secondary Attributes
-
Embedded
-
Primary Attributes
-
www.national.com
DS16EV5110 Device Description
The DS16EV5110 video equalizer comprises three data
channels, a clock channel, and a control interface including a
Systeml Management Bus (SMBus) port.
DATA CHANNELS
The DS16EV5110 provides three data channels. Each data
channel consists of an equalizer stage, a limiting amplifier, a
DC offset correction block, and a TMDS driver as shown in
Figure 3.
EQUALIZER BOOST CONTROL
The data channel equalizers support eight programmable lev-
els of equalization boost. The state of the FEB pin determines
how the boost settings are controlled. If the FEB pin is held
High, then the equalizer boost setting is controlled by the
Boost Set pins (BST_[0:2]) in accordance with Table 2. If this
programming method is chosen, then the boost setting se-
lected on the Boost Set pins is applied to all three data
channels. When the FEB pin is held Low, the equalizer boost
level is controlled through the SMBus. This programming
method is accessed via the appropriate SMBus registers (see
Table 1). Using this approach, equalizer boost settings can
be programmed for each channel individually. FEB is inter-
nally pulled High (default setting); therefore if left unconnect-
ed, the boost settings are controlled by the Boost Set pins
(BST_[0:2]). The range of boost settings provided enables the
DS16EV5110 to address a wide range of transmission line
path loss scenarios, enabling support for a variety of data
rates and formats.
DEVICE STATE AND ENABLE CONTROL
The DS16EV5110 has an Enable feature which provides the
ability to control device power consumption. This feature can
BC_2, BC_1,
Control Via
(FEB = 0)
SMBus
BC_0
000
001
010
011
100
101
110
111
TABLE 2. EQ Boost Control Table
Control Via Pins
BST_2, BST_1,
(FEB = 1)
BST_0
000
001
010
011
100
101
110
111
EQ Boost Setting
at 825 MHz (dB)
(TYP)
14
18
21
24
26
28
30
9
10
be controlled either via the Enable Pin (EN Pin) or via the
Enable Control Bit which is accessed through the SMBus port
(see Table 1 and Table 3). If Enable is activated, the data
channels and clock channel are placed in the ACTIVE state
and
DS16EV5110 can also be placed in STANDBY mode to save
power. In this mode only the control interface including the
SMBus port as well as the clock channel signal detection cir-
cuit remain active.
CLOCK CHANNEL
The clock channel incorporates a limiting amplifier, a DC off-
set correction, and a TMDS driver as shown in Figure 4.
CLOCK CHANNEL SIGNAL DETECT
The DS16EV5110 features a signal detect circuit on the clock
channel. The status of the clock signal can be determined by
either reading the Signal Detect bit (SD) in the SMBus regis-
ters (see Table 1) or by the state of the SD pin. A logic High
indicates the presence of a signal that has exceeded a spec-
ified threshold value (called SD_ON). A logic Low means that
the clock signal has fallen below a threshold value (called
SD_OFF). These values are programmed via the SMBus
(Table 1). If not programmed via the SMBus, the thresholds
take on the default values for the SD_OFF and SD_ON values
as indicated in Table 4. The Signal Detect threshold values
can be changed through the SMBus. All threshold values
specified are DC peak-to-peak differential signals (positive
signal minus negative signal) at the input of the device.
TABLE 4. Clock Channel Signal Detect Threshold Values
Register 07[0]
Bit 1 Bit 0
0
0
1
1
0 : Disable
0 : Disable
1 : Enable
1 : Enable
(SMBus)
all
TABLE 3. Enable and Device State Control
0
1
0
1
device
SD_OFF Threshold
Register 06 (mV)
(CMOS)
EN Pin
blocks
40 (Default)
X
X
1
0
30
55
45
function
Register 03[3]
(EN Control)
(SMBus)
X
X
0
1
as
SD_ON Threshold
Register 05 (mV)
70 (Default)
described.
Device State
STANDBY
STANDBY
55
90
75
ACTIVE
ACTIVE
The