EVAL-AD7693CBZ Analog Devices Inc, EVAL-AD7693CBZ Datasheet
EVAL-AD7693CBZ
Specifications of EVAL-AD7693CBZ
Related parts for EVAL-AD7693CBZ
EVAL-AD7693CBZ Summary of contents
Page 1
... AD768x/AD769x/AD794x/AD798x is available at www.analog.com and should be consulted when utilizing this evaluation board. The evaluation board is ideal for use with either Analog Devices EVAL-CONTROL BRD2/BRD3 (EVAL-CONTROL BRDx), DSP based controller board, to run the Analog devices evaluation software and to develop a specific application using LabVIEW stand-alone evaluation board. ...
Page 2
... EVAL-AD76XXCB 8/10-Pin TABLE OF CONTENTS Detailed Description .................................................................... 3 Using the EVAL-AD768x/AD769x/AD794xCB Software ...... 3 Testing Methods ........................................................................... 3 REVISION HISTORY 03/07—PrG Version 02/06—PrF Version 05/05—PrE Version Preliminary Technical Data Use as a Standalone Evaluation Board........................................4 Ordering Guide .......................................................................... 18 ESD Caution................................................................................ 18 Rev Page ...
Page 3
... EVAL-CONTROL BRDx and a 26-pin IDC connector for the serial output interface. The evaluation board is a four-layer board carefully laid out and tested to demonstrate the specific high accuracy performance of the AD768x/ AD769x/AD794x/AD798x. Figure 2 through Figure 5 show the schematics of the evaluation board. The ...
Page 4
... Preliminary Technical Data Use as a Standalone Evaluation Board You have the option of using the evaluation board as a stand- alone. This method does not require the EVAL-CONTROL BRDx, nor does it require use of the accompanied software. The ADC serial interface signals are available on P1 (26-pin connector) ...
Page 5
... V JP7 7 V JP8 12 V JP9 VDD JP10 +VA, +2.5V (for AD798x) JP11 3.3 V JP13 BUF+ JP25 BUF- Table 2. EVAL-AD768x/AD769x/AD794xCB Test Points Test Point TP1 TP2 TP3 TP4 TP5 TP6 TP7 TP8 TP9 TP10 TP11 TP12 TP13 Function Selection of the IN+ analog signal of U1 and U8, ADC0 and ADC1. ...
Page 6
... EVAL-AD76XXCB 8/10-Pin 8 4 GND 2 2.5/3v +VIN 8 2 GND 4 OVDD VDD REF GND Figure 2. Schematic (Analog section) Rev Page Preliminary Technical Data VDD 8 REF GND ...
Page 7
... Preliminary Technical Data Figure 3. Schematic (Digital Section) Rev Page EVAL-AD76XXCB 8/10-Pin ...
Page 8
... EVAL-AD76XXCB 8/10-Pin GND GND 5 Figure 4. Schematic (Power Section) Rev Page Preliminary Technical Data VDD GND GND GND 5 ...
Page 9
... Preliminary Technical Data 3 6 GND VDD DOUT 14 SCK DIN SYNC OVDD VDD VDD 8 REF GND REF GND 1 Figure 5. Schematic (Option Section) Rev Page EVAL-AD76XXCB 8/10-Pin ...
Page 10
... EVAL-AD76XXCB 8/10-Pin Figure 6. Top-Side Silk-Screen (Not to Scale). Figure 7. Top-Side (Not to Scale). Rev Page Preliminary Technical Data ...
Page 11
... Preliminary Technical Data Figure 8. Ground Layer (Not to Scale). Figure 9. Shield Layer (Not to Scale). Rev Page EVAL-AD76XXCB 8/10-Pin ...
Page 12
... EVAL-AD76XXCB 8/10-Pin Figure 10. Bottom-Side Layer (Not to Scale). Figure 11. Bottom-Side Silk-Screen (Not to Scale). Rev Page Preliminary Technical Data ...
Page 13
... This is the performance window. These controls are for locking and resetting the display axis to the data minimum and maximum values. 6) These gives direct access to datasheets and evaluation documentation. 5) This window allows the samples to be taken once (F3) or continuous (F4). Also selects: Help screen, Save data to Excel (F5), Print (F8) and Quit (F10). ...
Page 14
... EVAL-AD76XXCB 8/10-Pin These control the choice of chart type and X-units. Chart type selection of Histogram or Time and X-units of hexadecimal or Volts. The results are displayed in this chart. Also, the cursor (yellow) can be dragged desired location where the X-axis values and the Y-axis value will be displayed. ...
Page 15
... X-axis values and the Y-axis value will be displayed. Choice of either a Kaiser window or a Blackmann- Harris window from the is menu. Figure 14. FFT Screen Rev Page EVAL-AD76XXCB 8/10-Pin AC test results are displayed here. Also the choice of viewing the amplitude of a certain FFT component can be selected from the FFT component menu. ...
Page 16
... EVAL-AD76XXCB 8/10-Pin The AC test can also be displayed in the Time Domain as shown below. To view the Time domain output, select Time in this menu. Figure 15. Time-Domain Screen Rev Page Preliminary Technical Data ...
Page 17
... X-axis values and the Y-axis value will be displayed. The decimation ratio (Dratio) and number of Ksamples are entered here. The Nyquist frequency is displayed here as: F NYQUIST Figure 16. Decimated (Averaging) Screen Rev Page EVAL-AD76XXCB 8/10-Pin F = SAMPLE RATIO ...
Page 18
... ORDERING GUIDE Evaluation Board Model EVAL-AD7683CBZ EVAL-AD7684CBZ EVAL-AD7685CBZ EVAL-AD7686CBZ EVAL-AD7687CBZ EVAL-AD7688CBZ EVAL-AD7690CBZ EVAL-AD7691CBZ EVAL-AD7693CBZ EVAL-AD7694CBZ EVAL-AD7942CBZ EVAL-AD7946CBZ EVAL-AD7980CBZ EVAL-AD7982CBZ EVAL-CONTROL BRD2 EVAL-CONTROL BRD3 ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges ...