MAX110EVKIT-DIP Maxim Integrated Products, MAX110EVKIT-DIP Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX110EVKIT-DIP
Manufacturer Part Number
MAX110EVKIT-DIP
Description
EVAL KIT FOR MAX110
Manufacturer
Maxim Integrated Products
Specifications of MAX110EVKIT-DIP
Number Of Adc's
1
Number Of Bits
14
Sampling Rate (per Second)
50
Data Interface
Serial
Inputs Per Adc
2 Differential
Input Range
±VREF
Power (typ) @ Conditions
4.35mW @ 50SPS
Voltage Supply Source
Single Supply
Operating Temperature
0°C ~ 70°C
Utilized Ic / Part
MAX110, MAX111
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
10) Apply an input signal between the IN1+ and IN1-
11) To examine the bit patterns of the MAX110’s data
12) Before turning off power to the MAX110 EV kit, exit
This section applies only to the use of the MAX110 EV
kit by itself, without the 80C32 µC module.
1) Verify that shunts are installed at the proper loca-
2) Connect a regulated +5V DC power supply to the
3) Use a voltmeter to verify that at least -4.75V
4) Connect the interface signals to the DIN, DOUT,
5) Apply the input voltage to the input terminals. One
_________________________Quick Start
bottom half of each bar graph shows a rolling aver-
age of the readings for that channel. The AUTO
NULL switch is highlighted. With AUTO NULL and
GAIN CAL both off, the bar graphs read the real
voltage present at the input terminals of the
MAX110.
terminals of the MAX110 EV kit. Note that if
jumper JU7 is installed, then IN1- is connected to
ground. Observe the readout on the display screen.
input and output, press “B” to switch to the Bit
Manipulation Panel screen. The data input to the
MAX110 is displayed in the upper left corner, and
the output data is displayed in the lower left corner.
A rolling average display of the data received is
displayed underneath the most recently received
data. Data is displayed in hexadecimal and in bina-
ry. To switch back to the Control Panel, press “C”.
the program by pressing ALT+X.
tions. Table 1 shows the standard configuration. As
shipped from the factory, U1 is a MAX110, and the
voltage reference is 2.000V.
terminals labeled +5V and GND. The GND pad is
ground, and the +5V pad is the +5V input.
appears at the -5V pad, and verify that the voltage
reference between VREF+ and VREF- is 2.000V.
CS, BUSY, and SCK test points. Use the GND test
point as signal ground. See the MAX110 data sheet
for timing information.
channel is between IN1+ and IN1-, and the other
channel is between IN2+ and IN2-. If shunt J7 is
installed, then IN1- is connected to GND. If shunt J8
is installed, then IN2- is connected to GND. Be sure
to observe the absolute maximum ratings.
Stand-Alone MAX110 EV Kit
MAX110 Evaluation System/Evaluation Kit
_______________________________________________________________________________________
The MAX110 EV kit supports both the MAX110 and the
MAX111 ICs. To evaluate the MAX111 use the following
procedure:
1) While the EV kit is turned off, move J4 to the 2-3
2) Replace U1 with a MAX111.
3) Note that the MAX111 uses a 1.25V reference.
4) Follow the quick-start instructions for the MAX110.
The MAX111 output codes are identical to the MAX110
output codes. The input voltage range is more restricted
on the MAX111 because it is a single-supply device. Refer
to the MAX110/MAX111 data sheet for more information
on the MAX111’s input voltage range and accuracy.
For the MAX111, tie the V
the J4 shunt between pins 2 and 3. For the MAX110, tie
the V
pins 1 and 2.
Several jumper blocks allow different configurations of
the MAX110. Jumper functions and default settings are
shown in Tables 1 and 2.
To drive the MAX110 with an external clock, use the
following procedure:
1) Put a shunt across J5 pins 2-3, leaving pin 1 open.
2) Put a shunt across J1 pins 1-2, leaving pin 3 open.
3) Connect the external oscillator to the EXTCLK pad.
4) Connect the oscillator ground to the GND pin of
____________Evaluating the MAX111
Table 1. Default Jumper Settings
________________________of Hardware
position so that V
Replace resistor R11 with a 2.43kΩ resistor or
remove jumper J3 and apply an external 1.25V ref-
erence at VREF.
header H1.
SS
JUMPER
supply to -5V by installing the J4 shunt between
J1
J2
J3
J4
J5
J7
J8
J9
SS
Detailed Description
Using an External Clock
SS
= ground.
supply to GND by installing
DEFAULT SETTING
shorted by trace
shorted by trace
shorted by trace
closed
closed
Jumper Options
1-2
1-2
1-2
3