IRDC3629 International Rectifier, IRDC3629 Datasheet
IRDC3629
Related parts for IRDC3629
IRDC3629 Summary of contents
Page 1
... This user guide contains the schematic and bill of materials for the IR3629 evaluation board. The guide describes operation and use of the no evaluation board itself. Detailed under-voltage information for the IR3629 integrated circuit is available in the IR3629 data sheet. IRDC3629 =20A) o MOSFET for optimum cost and ...
Page 2
... Table I. Connections Signal Name V (+12V) in Ground Optional Vcc input Ground for optional Vcc input Ground of V out V (+1.8V) out Bias Voltage Ground IRDC3629 A maximum of 20A load can be 2 ...
Page 3
... V = 12V in Fig. 1 Connection diagram of the evaluation board for IR3629 (Top view) Fig. 2 Bottom view of the evaluation board for IR3629 IR3629 Demo Board IRDC3629 V =1. ...
Page 4
... IR3629 PCB Layers Top Layer Bottom Layer IRDC3629 4 ...
Page 5
... IR3629 PCB Layers PGND Mid-layer1 Mid-layer2 IRDC3629 AGND Single point connection between PGND and AGND 5 ...
Page 6
... IR3629 PCB Layers Mid-layer3 Mid-layer4 IRDC3629 6 ...
Page 7
... Q2 PGood N3065372 IRF6715 MX Vsens LDrv 9 4 Comp PGND Thermal R12 2.94K C9 N 1.96K 180pF 60.4K R3 30. IRDC3629 C4 C3 0.1uF 10uF C12 0.1uF SW L1 N3065200 1 2 0.36uH C15 C16 C17 C18 22uF 22uF 22uF 22uF R* 0 Vin Vin+ 1 Vin 10uF Vin- 33uF ...
Page 8
... Thick film, 1%, 1/10W Thick film, 1%, 1/10W Thick film, 1%, 1/10W Thick film, 1%, 1/10W Thick film, 1%, 1/10W Thick film, 1%, 1/10W Thick film, 1%, 1/10W Thick film, 1%, 1/10W Thick film, 1%, 1/10W Thick film, 1%, 1/10W IRDC3629 Size Manufacturer Part Number - Sanyo 25TQC33M 1206 Murata GRM31CR61C106KA88 603 ...
Page 9
... Description Thick film, 1%, 1/4W MLPD PWM Controller Banana Jack, Insulated, Solder Terminal, Black - Banana Jack, Insulated, Solder Terminal, Red - Banana Jack, Insulated, Solder Terminal, Green - IRDC3629 Size Manufacturer Part Number 1206 any 3x4 IR IR3629MPbF 603 - 603 Johnson Components 105-0853-001 Johnson Components ...
Page 10
... Fig. 4 Start Up at 20A Ch1:Vin, Ch2:Vss, Ch3:PGood, Ch4:Vout Fig. 6 Output Voltage Ripple at 20A Load Ch1:Vout, Ch3:SW Fig. 8 Transient Response Ch1:Vout, Ch2:Io(0-10A) IRDC3629 Fig. 5 Prebias Start Up Ch1:Vin, Ch2:Vss, Ch4:Vout Fig. 7 Gate Signals at 20A Load Ch1:LDRV, Ch2:HDRV, Ch3:SW Fig. 9 Shorted Hiccup Condition Recovery ...
Page 11
... TYPICAL OPERATING PERFORMANCE Vin=12.0V, Vo=1.8V, Io=0-20A, Fs=600kHz, Air Flow=200LFM Fig. 10 Bode Plot of Control Loop IRDC3629 11 ...
Page 12
... TYPICAL OPERATING PERFORMANCE Vin=12.0V, Vo=1.8V, Fs=600kHz, Room Temp, No Air Flow 100 0.0 Fig. 12 Thermal Image of IR3629 Demo Board at Io=15A IR3629 Efficiency 2.5 5.0 7.5 10.0 Iout(A) Fig. 11 Efficiency vs. Load 2 1 (1: IR3629, 2: IRF6715, 3: IRF6712) IRDC3629 12.5 15.0 12 ...
Page 13
... Copper (≥ 0.1mm for 1 oz. Copper and ≥ 0.23mm for 3 oz. Copper). Two 0.30mm diameter via should be placed in the center of the pad land and connected to ground to minimize the noise effect on the IC. IRDC3629 13 13 ...
Page 14
... IRDC3629 14 14 ...
Page 15
... The maximum length and width of the land pad stencil aperture should be equal to the solder resist opening minus an annular 0.2mm pull back to decrease the incidence of shorting the center land to the lead lands when the part is pushed into the solder paste. IRDC3629 15 15 ...
Page 16
... PITCH Figure A 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 Visit us at www.irf.com for sales contact information Data and specifications subject to change without notice. 02/01 IRDC3629 VGED-4 INCHES MAX MIN NOM MAX 1.00 .032 .035 .039 0.05 ...