LM2832ZSD EVAL National Semiconductor, LM2832ZSD EVAL Datasheet

no-image

LM2832ZSD EVAL

Manufacturer Part Number
LM2832ZSD EVAL
Description
BOARD EVAL LM2832ZSD
Manufacturer
National Semiconductor
Datasheets
1.LM2832YSDNOPB.pdf (27 pages)
2.LM2832ZSD_EVAL.pdf (6 pages)

Specifications of LM2832ZSD EVAL

Main Purpose
DC/DC, Step Down
Outputs And Type
1, Non-Isolated
Voltage - Output
1.8V
Current - Output
2A
Voltage - Input
3 ~ 5.5V
Regulator Topology
Buck
Frequency - Switching
3MHz
Board Type
Fully Populated
Utilized Ic / Part
LM2832
Lead Free Status / RoHS Status
Not applicable / Not applicable
Power - Output
-
© 2009 National Semiconductor Corporation
LM2832Z 6-Pin LLP Demo
Board
Introduction
The demo board included in this shipment converts 3V to 5.5V
input to 1.8V output for 2A load current using the LM2832Z
1.6 MHz DC-DC switching converter. This is a 4-layer board
using the internal layers as a VIN plane and Ground plane.
A bill of materials below describes the parts used on this demo
board. A schematic and layout have also been included below
Pin-Out
Pin Description 6-Pin LLP
DAP
Pin
1
2
3
4
5
6
Die Attach Pad
Name
VIND
VINA
GND
SW
EN
FB
Feedback pin. Connect to external resistor divider to set output voltage.
Signal and power ground pin. Place the bottom resistor of the feedback network as close
as possible to this pin.
Output switch. Connect to the inductor and catch diode.
Power Input supply.
Control circuitry supply voltage. Connect VINA to VIND on PC board.
Enable control input. Logic high enables operation. Do not allow this pin to float or be
greater than VINA + 0.3V.
Connect to system ground for low thermal impedance, but it cannot be used as a primary
GND connection.
LM2832Z 6-Pin LLP Demo Board Schematic
300010
National Semiconductor
Application Note 1553
Matthew Reynolds
January 8, 2009
along with measured performance characteristics. The above
restrictions for the input voltage are valid only for the demo
board as shipped with the demo board schematic below.
Operating Conditions
V
V
I
O
IN
O
= 2A
= 1.8V
= 3V to 5.5V
30001002
Function
www.national.com
30001001

Related parts for LM2832ZSD EVAL

Image
Part Number
Description
Manufacturer
Datasheet
Request R
LM2832ZSD/NOPB
Part Number:
LM2832ZSD/NOPB
Description:
IC REGULATOR BUCK 2A 6-LLP
Manufacturer:
National Semiconductor
Datasheet:
LM2832YSDNOPB.pdf (27 pages)
LM2832ZSD
Part Number:
LM2832ZSD
Description:
IC,SMPS CONTROLLER,CURRENT-MODE,BICMOS,LLCC,6PIN,PLASTIC
Manufacturer:
National Semiconductor
MC1408P8
Part Number:
MC1408P8
Description:
National Semiconductor [8-Bit D/A Converter]
Manufacturer:
National Semiconductor
Datasheet:
MC1408P8.pdf (12 pages)
CS1301
Part Number:
CS1301
Description:
National Semiconductor [Media Coprocessor]
Manufacturer:
National Semiconductor
Datasheet:
CS1301.pdf (25 pages)
LM4832N
Part Number:
LM4832N
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
LM4832N.pdf (23 pages)
LM4832M
Part Number:
LM4832M
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
LM4832M.pdf (23 pages)
LM4546
Part Number:
LM4546
Description:
AC97 Rev 2 Codec with Sample Rate Conversion and National 3D Sound
Manufacturer:
National Semiconductor
LP2981AIM5X-2.7
Part Number:
LP2981AIM5X-2.7
Description:
Manufacturer:
National Semiconductor
Datasheet:
LP2981AIM5X-2.7.pdf (16 pages)
LP2988AIMMX-3.8
Part Number:
LP2988AIMMX-3.8
Description:
Manufacturer:
National Semiconductor
LP3988IMFX-2.6
Part Number:
LP3988IMFX-2.6
Description:
Manufacturer:
National Semiconductor
Datasheet:
LP3988IMFX-2.6.pdf (11 pages)
LPV321M7X
Part Number:
LPV321M7X
Description:
General Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers
Manufacturer:
National Semiconductor
Datasheet:
LPV321M7X.pdf (21 pages)
ADC0882CCN
Part Number:
ADC0882CCN
Description:
8-bit 20 MSPS flash A/D converter.
Manufacturer:
National Semiconductor
Datasheet:
ADC0882CCN.pdf (11 pages)
LM837N
Part Number:
LM837N
Description:
Low Noise Quad Operational Amplifier
Manufacturer:
National Semiconductor
Datasheet:
LM837N.pdf (8 pages)
DS3650J
Part Number:
DS3650J
Description:
Quad Differential Line Receivers
Manufacturer:
National Semiconductor
Datasheet:
DS3650J.pdf (8 pages)
DS3662J
Part Number:
DS3662J
Description:
Quad High Speed Trapezoidal? Bus Transceiver
Manufacturer:
National Semiconductor
Datasheet:
DS3662J.pdf (6 pages)

LM2832ZSD EVAL Summary of contents

Page 1

... VIND 5 VINA 6 EN DAP Die Attach Pad © 2009 National Semiconductor Corporation National Semiconductor Application Note 1553 Matthew Reynolds January 8, 2009 along with measured performance characteristics. The above restrictions for the input voltage are valid only for the demo board as shipped with the demo board schematic below. ...

Page 2

LM2832 Gain/Phase LM2832 Efficiency: Vin = 3.3V 1.8V www.national.com 30001003 2 30001004 30001005 ...

Page 3

Part Buck Regulator C1, Input Cap C2 Output Cap C3 Output Cap D1, Catch Diode 0. – R9 Layout Bill Of Materials LM2832Z-Version Part Value Manufacturer NSC 22 µF, 6.3V, X5R ...

Page 4

Internal Plane 1 (GND) 4 30001007 ...

Page 5

Internal Plane Bottom Layer 5 30001008 30001009 www.national.com ...

Page 6

... For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Amplifiers www.national.com/amplifiers Audio www.national.com/audio Clock and Timing www.national.com/timing Data Converters www.national.com/adc Interface www.national.com/interface LVDS www.national.com/lvds Power Management www.national.com/power Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www ...

Related keywords