LM25575EVAL National Semiconductor, LM25575EVAL Datasheet
LM25575EVAL
Manufacturer Part Number
LM25575EVAL
Description
BOARD EVALUATION FOR LM25575
Manufacturer
National Semiconductor
Series
PowerWise®, SIMPLE SWITCHER®r
Datasheets
1.LM25575MHXNOPB.pdf
(24 pages)
2.LM25575BLDTNOPB.pdf
(4 pages)
3.LM25575EVAL.pdf
(6 pages)
Specifications of LM25575EVAL
Main Purpose
DC/DC, Step Down
Outputs And Type
1, Non-Isolated
Voltage - Output
5V
Current - Output
1.5A
Voltage - Input
7 ~ 42V
Regulator Topology
Buck
Frequency - Switching
300kHz
Board Type
Fully Populated
Utilized Ic / Part
LM25575
Lead Free Status / RoHS Status
Not applicable / Not applicable
Power - Output
-
Other names
*LM25575EVAL
© 2007 National Semiconductor Corporation
LM25575 Evaluation Board
Introduction
The LM25575 evaluation board is designed to provide the
design engineer with a fully functional power converter based
on Emulated Current Mode Control to evaluate the LM25575
regulator IC. The evaluation board provides a 5V output with
a 1.5A current capability. The ultra-wide input voltage ranges
from 7V to 42V. The design operates at 300kHz, a good com-
promise between conversion efficiency and solution size. The
printed circuit board consists of 2 layers of 2 ounce copper on
FR4 material with a thickness of 0.06 inches. This application
note contains the evaluation board schematic, Bill-of-Materi-
als (BOM) and a quick setup procedure. Refer to the LM25575
datasheet for complete circuit design information.
Evaluation Board Schematic
Powering and Loading
Considerations
Read this entire page prior to attempting to power the evalu-
ation board.
QUICK SETUP PROCEDURE
Step 1: Set the power supply current limit to 1.8A. Turn off
the power supply. Connect the power supply to the Vin ter-
minals.
Step 2: Connect the load, with a 1.5A capability, to the Vout
terminals. Positive connection to J2 and negative connection
to J3.
300070
National Semiconductor
Application Note 1578
Robert Bell
January 2007
The performance of the evaluation board is as follows:
Input Range: 7 to 42V
Output Voltage: 5V
Output Current: 0 to 1.5A
Frequency of Operation: 300 KHz
Board Size: 2.6 X 1 X 0.4 inches
Load Regulation: 1%
Line Regulation: 0.1%
Over Current Limiting
Step 3: The SD pin should be left open for normal operation.
Step 4: Set Vin to 24V with no load applied. Vout should be
in regulation with a nominal 5V output.
Step 5: Slowly increase the load while monitoring the output
voltage, Vout should remain in regulation with a nominal 5V
output as the load is increased up to 1.5 Amps.
Step 6: Slowly sweep the input voltage from 7 to 42V, Vout
should remain in regulation with a nominal 5V output.
Step 7: Temporally short the SD pin to GND to check the
shutdown function.
Step 8: Increase the load beyond the normal range to check
current limiting. The output current should limit at approxi-
mately 2.1A. The power supply (Vin source) current limit may
www.national.com
30007001
Related parts for LM25575EVAL
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
National Semiconductor [8-Bit D/A Converter]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
National Semiconductor [Media Coprocessor]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
AC97 Rev 2 Codec with Sample Rate Conversion and National 3D Sound
Manufacturer:
National Semiconductor
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
General Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
8-bit 20 MSPS flash A/D converter.
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Low Noise Quad Operational Amplifier
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Quad Differential Line Receivers
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Quad High Speed Trapezoidal? Bus Transceiver
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Dual Line Receiver
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
TTL to 10k ECL Level Translator with Latch
Manufacturer:
National Semiconductor
Datasheet:
LM25575EVAL Summary of contents
Page 1
... Connect the power supply to the Vin ter- minals. Step 2: Connect the load, with a 1.5A capability, to the Vout terminals. Positive connection to J2 and negative connection to J3. © 2007 National Semiconductor Corporation National Semiconductor Application Note 1578 Robert Bell January 2007 ...
Page 2
Cooling is critical during this step. AIR FLOW Prolonged operation with high input voltage at full power will cause the thermal shutdown circuit within the regulator IC to activate. A stand-alone fan with ...
Page 3
... CAPACITOR, CER, KEMET NOT USED DIODE, 60V, CENTRAL INDUCTOR, COOPER NOT USED NOT USED RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR REGULATOR, NATIONAL SEMICONDUCTOR 3 VALUE 1µ, 100V 1µ, 100V 470p, 100V 0.01µ, 100V 0.01µ, 100V 0.022µ, 100V 0.47µ, 16V 10µ, 16V 120µ ...
Page 4
PCB Layout www.national.com Component Side Solder Side Silkscreen 4 30007005 30007006 30007007 ...
Page 5
Notes 5 www.national.com ...
Page 6
... National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. ...