EVAL-AD5449EBZ Analog Devices Inc, EVAL-AD5449EBZ Datasheet - Page 20
![BOARD EVALUATION FOR AD5449](/photos/9/15/91596/eval-ad5449eb_board_sml.jpg)
EVAL-AD5449EBZ
Manufacturer Part Number
EVAL-AD5449EBZ
Description
BOARD EVALUATION FOR AD5449
Manufacturer
Analog Devices Inc
Specifications of EVAL-AD5449EBZ
Number Of Dac's
2
Number Of Bits
12
Outputs And Type
2, Differential
Sampling Rate (per Second)
2.47M
Data Interface
Serial
Settling Time
80ns
Dac Type
Current
Voltage Supply Source
Single
Operating Temperature
-40°C ~ 125°C
Utilized Ic / Part
AD5449
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD5429/AD5439/AD5449
SERIAL INTERFACE
The AD5429/AD5439/AD5449 have an easy-to-use, 3-wire
interface that is compatible with SPI, QSPI, MICROWIRE, and
most DSP interface standards. Data is written to the device in
16-bit words. Each 16-bit word consists of four control bits and
eight, 10, or 12 data bits, as shown in Figure 44 through Figure 46.
Low Power Serial Interface
To minimize the power consumption of the device, the interface
powers up fully only when the device is being written to, that is,
on the falling edge of SYNC . The SCLK and SDIN input buffers
are powered down on the rising edge of SYNC .
DAC Control Bit C3 to Control Bit C0
Control Bit C3 to Control Bit C0 allow control of various functions
of the DAC, as shown in Table 11. The default settings of the DAC
at power-on are such that data is clocked into the shift register
on falling clock edges and daisy-chain mode is enabled. The device
powers on with a zero-scale load to the DAC register and I
The DAC control bits allow the user to adjust certain features at
power-on. For example, daisy-chaining can be disabled if not in
use, an active clock edge can be changed to a rising edge, and DAC
output can be cleared to either zero scale or midscale. The user
can also initiate a readback of the DAC register contents for veri-
fication.
Control Register (Control Bits = 1101)
While maintaining software compatibility with single-channel
current output DACs (AD5426/AD5432/AD5443), these DACs
also feature additional interface functionality. Set the control bits
to 1101 to enter control register mode. Figure 47 shows the
contents of the control register, the functions of which are
described in the following sections.
DB15 (MSB)
DB15 (MSB)
DB15 (MSB)
DB15 (MSB)
C3
C3
C3
1
CONTROL BITS
CONTROL BITS
CONTROL BITS
CONTROL BITS
C2
C2
C2
1
C1
C1
C1
0
C0
C0
C0
1
Figure 45. AD5439 10-Bit Input Shift Register Contents
Figure 46. AD5449 12-Bit Input Shift Register Contents
Figure 44. AD5429 8-Bit Input Shift Register Contents
SDO2
DB11
DB7
DB9
Figure 47. Control Register Loading Sequence
DB10
SDO1
DB6
DB8
OUT
lines.
DB5
DB7
DB9
DSY
Rev. C | Page 20 of 32
HCLR
DB4
DB6
DB8
SCLK
DB3
DB5
DB7
SDO Control (SDO1 and SDO2)
The SDO bits enable the user to control the SDO output driver
strength, disable the SDO output, or configure it as an open-drain
driver. The strength of the SDO driver affects the timing of t
and, when stronger, allows a faster clock cycle.
Table 10. SDO Control Bits
SDO2
0
0
1
1
Daisy-Chain Control (DSY)
DSY allows the enabling or disabling of daisy-chain mode.
A 1 enables daisy-chain mode; a 0 disables daisy-chain mode.
When disabled, a readback request is accepted; SDO is auto-
matically enabled; the DAC register contents of the relevant
DAC are clocked out on SDO; and, when complete, SDO is
disabled again.
Hardware CLR Bit (HCLR)
The default setting for the hardware CLR bit is to clear the registers
and DAC output to zero code. A 1 in the HCLR bit allows the
CLR pin to clear the DAC outputs to midscale, and a 0 clears to
zero scale.
Active Clock Edge (SCLK)
The default active clock edge is a falling edge. Write a 1 to this
bit to clock data in on the rising edge, or a 0 to clock it in on the
falling edge.
DB2
DB4
DB6
DATA BITS
DATA BITS
DATA BITS
X
DB1
DB3
DB5
X
SDO1
0
1
0
1
DB0
DB2
DB4
X
DB1
DB3
0
X
Function Implemented
Full SDO driver
Weak SDO driver
SDO configured as open drain
Disable SDO output
DB0
DB2
0
X
DB1
0
0
X
DB0 (LSB)
DB0 (LSB)
DB0 (LSB)
DB0 (LSB)
DB0
0
0
X
12
,