MAX16828EVKIT+ Maxim Integrated Products, MAX16828EVKIT+ Datasheet

no-image

MAX16828EVKIT+

Manufacturer Part Number
MAX16828EVKIT+
Description
EVALUATION KIT FOR MAX16828
Manufacturer
Maxim Integrated Products
Datasheets

Specifications of MAX16828EVKIT+

Current - Output / Channel
200mA
Outputs And Type
1, Non-Isolated
Features
Dimmable, Extra 5V Output
Voltage - Input
6.5 ~ 40V
Utilized Ic / Part
MAX16828
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
The MAX16828 evaluation kit (EV kit) is a fully assem-
bled and tested PCB that demonstrates a current-
controlled, high-output-current LED driver with accurate
current control based on the MAX16828 current regula-
tor. The EV kit features pulse-width modulation (PWM)
dimming control and is configured for preset output
currents of 100mA or 200mA. The EV kit can operate
from a single power supply at voltages between 6.5V
and 40V. The MAX16828 EV kit also evaluates the
MAX16815 IC; contact the factory for a free sample of
the MAX16815 IC.
Warning : Under severe fault or failure conditions, this
EV kit may dissipate large amounts of power. Operate
this EV kit with care to avoid possible personal injury.
19-4394; Rev 0; 12/08
Note : Indicate that you are using the MAX16828 when contacting these component suppliers.
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
Murata Electronics North America, Inc.
Susumu International USA
TDK Corp.
DESIGNATION
C1, C2
R2, R3
JU1
R1
SUPPLIER
________________________________________________________________ Maxim Integrated Products
QTY
2
1
1
2
General Description
0.1µF ±10%, 50V X7R ceramic
capacitors (0603)
Murata GRM188R71H104K
TDK C1608X7R1H104K
2-pin header
100kΩ ±5% resistor (0603)
1Ω, 1/4W ±1% resistors (0805)
Susumu RL12205-1R0-F
DESCRIPTION
770-436-1300
208-328-0307
847-803-6100
PHONE
MAX16828 Evaluation Kit
o 6.5V to 40V Input Supply Voltage Range
o 100mA/200mA Output Current
o Wide-Range Dimming Control with PWM
o 5V Regulated Output with 4mA Source Capability
o Lead(Pb)-Free and RoHS Compliant
o Fully Assembled and Tested
+Denotes lead(Pb)-free and RoHS compliant.
* EP = Exposed pad.
MAX16828EVKIT+
DESIGNATION
PART
U1
V5
www.murata-northamerica.com
www.susumu-usa.com
www.component.tdk.com
QTY
1
1
1
1
Component Suppliers
Ordering Information
200m A ad j ustab l e hi g h- b r i g htness
LED driver (6 TDFN-EP*)
Maxim MAX16828ATT+
Test point
Shunt
PCB: MAX16828 Evaluation Kit+
WEBSITE
Component List
DESCRIPTION
TYPE
EV Kit
Features
1

Related parts for MAX16828EVKIT+

MAX16828EVKIT+ Summary of contents

Page 1

... Input Supply Voltage Range o 100mA/200mA Output Current o Wide-Range Dimming Control with PWM o 5V Regulated Output with 4mA Source Capability o Lead(Pb)-Free and RoHS Compliant o Fully Assembled and Tested Ordering Information PART MAX16828EVKIT+ +Denotes lead(Pb)-free and RoHS compliant. DESIGNATION QTY — ...

Page 2

MAX16828 Evaluation Kit Recommended Equipment Before beginning, the following equipment is needed: • 30V or above, 0.5A DC power supply The MAX16828 EV kit is fully assembled and tested. Follow the steps below to verify board operation. Caution: ...

Page 3

Figure 1. MAX16828 EV Kit Schematic _______________________________________________________________________________________ MAX16828 Evaluation Kit 3 ...

Page 4

... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 4 ___________________ Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2008 Maxim Integrated Products Figure 3. MAX16828 EV Kit PCB Layout— ...

Related keywords