LP3991TL-1.2EV National Semiconductor, LP3991TL-1.2EV Datasheet - Page 4

• Manufacturer Part Number: LP3991TL-1.2EV
• Description: BOARD EVALUATION LP3991TL-1.2
• Manufacturer: National Semiconductor
• Series: PowerWise®r

Specifications of LP3991TL-1.2EV

• Channels Per Ic: 1 - Single
• Voltage - Output: 1.2V
• Current - Output: 300mA
• Voltage - Input: 1.65 ~ 4V
• Regulator Type: Positive Fixed
• Operating Temperature: -40°C ~ 85°C
• Board Type: Fully Populated
• Utilized Ic / Part: LP3991
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

www.national.com
Enable Control Characteristics
I
(Note
V
V
Timing Characteristics
T
Transient
Response
I
EN
IR
ON
IL
IH
Electrical Characteristics con't.
Unless otherwise noted, V
Typical values and limits appearing in normal type apply for T
temperature range for operation, −40 to +125°C.
Note 1: Absolute Maximum Ratings are limits beyond which damage can occur. Operating Ratings are conditions under which operation of the device is
guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical
Characteristics tables.
Note 2: All Voltages are with respect to the potential at the GND pin.
Note 3: For further information on these packages please refer to the following application notes,AN-1112 Micro SMD Wafer Level Chip Scale Package.
Note 4: Internal thermal shutdown circuitry protects the device from permanent damage.
Note 5: The human body model is 100pF discharged through a 1.5kΩ resistor into each pin. The machine model is a 200pF capacitor discharged directly into
each pin.
Note 6: The maximum ambient temperature (T
dissipation of the device in the application (P
following equation: T
Note 7: Junction to ambient thermal resistance is dependant on the application and board layout. In applications where high maximum power dissipation is
possible, special care must be paid to thermal dissipation issues in board design.
Note 8: Full details can be found in JESD61-7
Note 9: All limits are guaranteed. All electrical characteristics having room-temperature limits are tested during production at T
Statistical Quality Control methods. Operation over the temperature specification is guaranteed by correlating the electrical characteristics to process and
temperature variations and applying statistical process control.
Note 10: V
Note 11: Dropout voltage is voltage difference between input and output at which the output voltage drops to 100mV below its nominal value. This parameter is
only specified for output voltages above 1.8V.
Note 12: The device maintains the regulated output voltage without a load.
Note 13: Short circuit current is measured with V
Note 14: This electrical specification is guaranteed by design.
Note 15: Enable Pin has an internal 1.2MΩ typical, resistor connected to GND.
Note 16: The device will operate with input voltages up to 4.0V. However special care should be taken in relation to thermal dissipation and the need to derate
the maximum allowable ambient temperature. See
Symbol
15)
IN(MIN)
Maximum Input Current at
V
Low Input Threshold
High Input Threshold
Turn On Time
Line Transient Response |δV
Load Transient Response |δV
Overshoot on Start-up
In-Rush Current
EN
= V
Input
A(max)
OUT(NOM)
= T
Parameter
+ 0.5V or 1.65V, whichever is greater. (See post DC/DC convertor example in application information section).
J(max-op)
EN
(Note
(Note
=950mV, V
- (θ
14)
JA
14)
× P
D(max)
A(max)
D(max)
OUT
), and the junction to ambient thermal resistance of the part / package in the application (θ
IN
OUT
(Note
OUT
) is dependant on the maximum operating junction temperature (T
).
= V
pulled to 0V.
| T
| T
OUT
6,
V
V
V
V
To 95% Level
V
δV
(Note
Note
rise
rise
EN
EN
IN
IN
IN(MIN)
(Note
IN
+ 0.5V, or 1.8V, whichever is higher. C
= 1.65V to 3.6V
= 1.65V to 3.6V
= 0V, V
= V
= T
= T
= 600mV
7)
14)
to 3.6V
IN
fall
fall
9)
= 3.6V
= 30µs
= 1µs
IN
A
= 25°C. Limits appearing in boldface type apply over the full junction
Conditions
= 3.6V
4
V
V
I
I
I
I
I
I
I
I
I
(Note
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
= 0 mA to 300mA
= 1mA to 300mA
= 300mA to 1mA
= 0mA to 200mA
= 1mA to 200mA
= 200mA to 1mA
= 0mA to 150mA
= 1mA to 150mA
= 150mA to 1mA
≤
> 2.0V
14)
2.0V
IN
0.001
Typ
100
140
140
110
110
100
600
= 1µF, I
80
80
60
70
50
3
6
0
J(max-op)
OUT
0.95
Min
= 125°C), the maximum power
J
= 1.0mA, C
= 25°C or correlated using
Limit
1000
Max
5.5
0.4
JA
2
OUT
), as given by the
=4.7µF.
(pk - pk)
Units
mV
mV
mA
µA
µs
%
V
V