STEVAL-MKI062V2 STMicroelectronics, STEVAL-MKI062V2 Datasheet - Page 22

• Manufacturer Part Number: STEVAL-MKI062V2
• Description: BOARD EVAL FOR MEMS SENSORS
• Manufacturer: STMicroelectronics
• Series: iNEMOr

Specifications of STEVAL-MKI062V2

• Design Resources: STEVAL-MKI062V2 Gerber Files STEVAL-MKI062V2 Schematic STEVAL-MKI062V2 Bill of Materials
• Sensor Type: Accelerometer, Gyroscope, Magnetometer, Pressure, Temperature
• Sensing Range: ±2g,4g,8g; 300 ~ 1100mbar; 300°/sec; -55 ~125°C
• Interface: I²C, USB
• Sensitivity: Multiple
• Voltage - Supply: 5V, USB
• Embedded: Yes, MCU, 32-Bit
• Utilized Ic / Part: LPR430AL, LY330ALH, LSM303DLH, LPS001DL, STM32F103RE, STLM75
• Interface Type: USB, CAN, I2C
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 55 C
• Silicon Manufacturer: STMicroelectronics
• Kit Application Type: Sensor
• Application Sub Type: MEMS Device
• Silicon Family Name: INEMO
• Kit Contents: MicroSD Card Slot, COM Connector, Reset Button,
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: STM32F103RE
• Other names: 497-10508

STM32-MEMS development kit
Table 12.
7.2.1
7.2.2
22/42
MEMS_SPI_WriteReg
MEMS_SPI_ReadReg
MEMS_SPI_SendFrame
MEMS_SPI_ReceiveFrame
MEMS_I2C_Setup
MEMS_I2C_Set_Address
MEMS_I2C_WriteReg
MEMS_I2C_ReadReg
MEMS_I2C_SendFrame
MEMS_I2C_ReceiveFrame
Function name
MEMS Library functions
MEMS_ANL_Setup function
Table 13
Table 13.
MEMS_ANL_Drive_FS function
Table 14
Table 14.
Function prototype
Description
Input parameter
Output parameter
Return parameter
Function prototype
Description
Input parameter
Output parameter
Return parameter
Function name
Function name
describes the MEMS_ANL_Setup function.
describes the MEMS_ANL_Drive_FS function.
MEMS_ANL_Setup function
MEMS_ANL_Drive_FS function
Writes data to the MEMS register over the SPI.
Reads data to the MEMS register over the SPI.
Sends one frame over the SPI.
Receives one frame over the SPI.
Sets-up all peripherals related to the digital MEMS connected over the I
Sets the address of the MEMS for I
Writes data to the MEMS register over the I
Reads data from the MEMS register over the I
Sends one frame over the I
Receives one frame over the I
void MEMS_ANL_Setup (void)
Sets-up all peripherals related to the analog MEMS.
None
None
None
void MEMS_ANL_Drive_FS (BitAction BitVal)
Drives the FS pin of the analog MEMS.
BitVal: new value of the FS pin
BitVal must be one of the BitAction enum values:
– Bit_RESET: clears the port pin
– Bit_SET: sets the port pin
None
None
Doc ID 15703 Rev 1
2
C.
2
C.
Description
MEMS_ANL_Drive_FS
MEMS_ANL_Setup
2
C communication.
2
C.
2
C.
UM0701
2
C.