STEVAL-MKI005V1 STMicroelectronics, STEVAL-MKI005V1 Datasheet - Page 37

• Manufacturer Part Number: STEVAL-MKI005V1
• Description: BOARD EVAL ACCELEROM LIS3LV02DL
• Manufacturer: STMicroelectronics
• Series: MEMSr

Specifications of STEVAL-MKI005V1

• Design Resources: STEVAL-MKI005V1 Gerber Files STEVAL-MKI005V1 Schematic STEVAL-MKI005V1 Bill of Materials
• Sensor Type: Accelerometer, 3 Axis
• Sensing Range: ±2g, 6g
• Interface: SPI, USB
• Sensitivity: 340 or 1024 LSb/g
• Voltage - Supply: 5V
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: LIS3LV02DL
• Acceleration: 2 g, 6 g
• Sensing Axis: Triple Axis
• Output Type: Digital
• Interface Type: USB
• Silicon Manufacturer: ST Micro
• Silicon Core Number: LIS3LV02DL
• Kit Application Type: Sensing - Motion / Vibration / Shock
• Application Sub Type: Accelerometer
• Kit Contents: Board
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-6226

UM0701
7.6.2
Chip selection
Depending on the type of architecture, the user has to select either an analog or digital
MEMS device. After, depending on the precision needed, the user will choose either the
LIS344ALH or LIS3LV02DL, if small-angle detection is required. If such a level of precision
is not needed, one can use the LIS302SG or LIS302DL. If the z axis is not affected (the
device is supposed to tilt around the z axis), a 2-axis accelerometer could be used.
Example 1
In the case of the LIS3LV02DL, the resolution is 1 mg per lsb. Thus, for an acceleration
variation of 1 mg, the angle measured on the z axis will be cos
axis, the angle detection will be sin
measurable is therefore 0.057°. This difference between the x and z axis is explained by the
behavior of the sine/cosine function.
Example 2
In the case of the LIS344ALH, the resolution is given by the formula [noise
density*rt(BW*correction factor)]. BW is the bandwidth and the correction factor is linked to
the low-pass filtering for the V
variation of 0.625 mg, the angle detection on the z axis will be cos
the x axis, the angle detection will be sin
Example 3
In the case of the LIS302DL, the resolution is 18 mg per lsb. Thus, for an acceleration
variation of 18 mg, the angle measured on the z axis will be cos
axis, the angle detection will be sin
Example 4
For the LIS302SG the resolution is 2.5 mg. Thus, the smallest angle variation measurable is
0.14°.
Due to the behavior of the sine/cosine functions and the angle and precision expected, the
user will have to consider the measured acceleration on one or all axes.
OUT
Doc ID 15703 Rev 1
. The resolution is 0.625 mg. Thus, for an acceleration
–1
–1
(10
(18
–3
–3
–1
) = 0.057°. The smallest angle variation
) = 1°.
(0.625*10
–3
) = 0.036°.
STM32-MEMS development kit
–1
–1
(1–10
(1-18
–1
(1-0.625*10
–3
–3
) = 2.5°. For the x
) = 10.9°. For the x
–3
) = 2°. For
37/42