LM95245EB/NOPB National Semiconductor, LM95245EB/NOPB Datasheet
LM95245EB/NOPB
Specifications of LM95245EB/NOPB
Related parts for LM95245EB/NOPB
LM95245EB/NOPB Summary of contents
Page 1
... LM95245EVAL/NOPB Evaluation Board User’s Guide © Copyright 2007 National Semiconductor Corporation LM95245EVAL 1 Revision B October 25, 2007 www.national.com ...
Page 2
... Introduction 2.0 Quick Start 3.0 Functional Description 4.0 Software Installation and Operation 5.0 Electrical and Mechanical Specifications 5.1 Electrical Specifications 5.2 Electrical Schematic 5.3 Evaluation Board Layout 5.4 Bill of Materials 5.5 Mechanical Specifications © Copyright 2007 National Semiconductor Corporation Table of Contents ...
Page 3
... SensorEval Version 1.1.0d beta or later, Evaluation Board CD containing: a. The SensorEval.exe executable program used to run the LM95245 Evaluation Board softcopy of this User’s Guide c. A readme.txt file with useful information about the program softcopy of the SensorEval Software manual. © Copyright 2007 National Semiconductor Corporation References 3 www.national.com ...
Page 4
... Introduction The LM95245EVAL/NOPB Evaluation Board is used together with the National Semiconductor SensorEval software (provided in the kit), and with a USB cable (not provided in the kit), and with an external personal computer (PC). LM95245EVAL/NOPB Evaluation Board is provide by the +5 VDC line of the USB connection. No external power supply or signal sources are required for operation of the LM95245 evaluation board ...
Page 5
... The next screen (first screen after the first run of the program) will look like this: Select the LM95245 Evaluation Board. Click OK. © Copyright 2007 National Semiconductor Corporation 5. The next screen will look like this: In order to enable proper temperature readings of the MMBT3904 transistor available on the LM95245EVAL do the following. ...
Page 6
... If the user clicks on the Start Plot button a graph box will appear and will graph the temperature. An © Copyright 2007 National Semiconductor Corporation example is shown below The sampled data can also be save in a Log file by selecting “Start Log”. Setup for the Log file can be found under the “ ...
Page 7
... Quick Start Diagram Important! NO EXTERNAL POWER SUPPLY OR SIGNAL INPUTS ARE REQUIRED! USB 2.0 or USB 1.1 connection SensorEval Software installed in the computer. © Copyright 2007 National Semiconductor Corporation N National Semiconductor Single Remote Diode Eval. Board Rev. 1 Pin 1 of Temp Sensor 7 Q1 ...
Page 8
... To Remote Diode Temp Sensor input © Copyright 2007 National Semiconductor Corporation VDC is the input to the on-board LM2950 low dropout voltage regulator, which regulates the output voltage to +3.3 VDC. This output voltage powers the LM95245, the on-board microcontroller, and the EEPROM chip where the board ID information is stored ...
Page 9
... J5, J6 These are jumpered as indicated if the LM95245 is in the A0 Address Select function mode. © Copyright 2007 National Semiconductor Corporation Pin Number USB Cable Input. Connect the USB cable to this jack after N/A the SensorEval software has been loaded on the PC The +3.3 VDC voltage supplied by the on-board ...
Page 10
... Follow the following procedure for operation the LM95245 Evaluation Board using the SensorEval software: 3. Run the SensorEval program by either double- clicking on the icon on the desktop or by selecting Start, Program Files, National Semiconductor, National SensorEval. 4. Plug in the USB cable on both the PC and the LM95245 Evaluation Board. © ...
Page 11
... The Board uses the +5.0 VDC and GND lines from the USB connection. This +5.0 VDC voltage is regulated down to +3.3 VDC for board power EXTERNAL POWER SUPPLY INPUTS ARE REQUIRED * 5.2 Electrical Schematic Schematic of the LM95245EVAL/NOPB Evaluation Board © Copyright 2007 National Semiconductor Corporation +5.0 ± 0.1 V, 100 mA max. 11 www.national.com ...
Page 12
... Evaluation Board Layout Figure 5.3 Layout diagram of the LM95245EVAL/NOPB Evaluation Board © Copyright 2007 National Semiconductor Corporation 12 www.national.com ...
Page 13
... NSC NOT SOLDER THE FOLLOWING TO BOARD 25 1 R18 (for USB 1.1 only R16 © Copyright 2007 National Semiconductor Corporation Eval Board Value 2.2 uF 100 pF 100 pF 2 Connector, USB-B CONN, 2X2 Headers, 0.1 in centers CONN, 1X2 Headers, 0.1 in centers CONN, 1X6 Headers, 0.1 in centers CONN, 1X1 Headers, 0 ...
Page 14
... Operating Mechanical and Environmental Specifications Minimum Temperature 5.4.2 Evaluation Board Basic Dimensions 5.4.3 Electrostatic Discharge (ESD) Precautions The user shall use ESD precautions as specified in National Semiconductor ESD control document (SC)CSI-3-038 available through www.national.com © Copyright 2007 National Semiconductor Corporation Typical 0° ...
Page 15
... BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9- 111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. ...