AS5046 AB austriamicrosystems, AS5046 AB Datasheet
AS5046 AB
Specifications of AS5046 AB
Related parts for AS5046 AB
AS5046 AB Summary of contents
Page 1
... Provision for a 600mil DIP socket Hole in PCB to center a 6mm magnet at the bottom of the IC LED for MagRng output On-board 5V linear voltage regulator for 7.5…12V supplies 9V battery connector for standalone operation Dimensions: 35mm x 37mm (1.38 x 1.46 inch) Revision 1.0 www.austriamicrosystems.com ADAPTER PCB OPERATION MANUAL Page ...
Page 2
... VDD5V VDD3V3 NC NC Vout FB DACout DACref www.austriamicrosystems.com Description Magnet Field Magnitude RaNGe warning; active low, indicates that the magnetic field strength is outside of the recommended limits. Mode input. Select between low noise (open, low) and high speed (high) mode. Internal pull-down resistor Chip Select, active low ...
Page 3
... Default) or 384µs (2.6kHz). The digital angle information is available in several formats: as serial 10-bit data stream, as pulse-width modulated (PWM) signal or as quadrature incremental signal. www.austriamicrosystems.com Page ...
Page 4
... Ext. voltage regulator Digital I/O level IC2 or IC3 not required *) 3.0….3.6V not required *) 4.5….5.5V 3.3V type, e.g. LE33C (ST 3.3V Micro) 5.0V type 5.0V e.g. 75L05 www.austriamicrosystems.com Remark short VDD5V and VDD3V3 short VDD5V and VDD3V3 PCB delivery status Page ...
Page 5
... The hole in the PCB underneath the chip allows centering of a 6mm diameter magnet. A Vout Led and voltage regulators are optional. Minimum required components are C4 (1µF) and the CSN pull- down R7 (0…4k7). Layout: Bottom View Revision 1.0 AS5046 Adapter Board: Top View Layout: Bottom Components www.austriamicrosystems.com Page ...
Page 6
... Supporting Tools austriamicrosystems provides the following tools for developments using the AS5046 rotary encoder IC: AS5046 Demoboard (see Figure 8) AS5046 Demoboard Operation Manual AS5046 Demoboard Software AS5046 Adapter PCB (see Error! Reference source not found.) AS5000 Encoder Software Development Kit (SDK) These supporting tools are available at local distributors http://www ...
Page 7
... As input device for the AS5046 demoboard software This configuration uses the same hardware connection as 8.1.2, but additionally the AS5046 demoboard software is running. All indicators on the demoboard will be displayed on the PC screen as well. Figure 8: AS5046 demoboard and adapter PCB Revision 1.0 www.austriamicrosystems.com Page ...
Page 8
... The 8-pin female connector is designed to fit directly onto the AS5046 Demoboard and use the Adapter PCB as external encoder (software setting: Encoder = external). Revision 1.0 www.austriamicrosystems.com Page ...
Page 9
... Adapter PCB to prevent accidental damage of the IC when an input voltage is applied to the regulator (and the 5V output is fed to the VDD3V3 supply pin) Figure 9: Configuring the adapter PCB for 3.3V operation (see Figure 10) Revision 1.0 www.austriamicrosystems.com Page ...
Page 10
... If longer cables are used, a pull-down resistor at the DO line of 22k - 56k Ohms is recommended to discharge the signal between data transmissions and no static voltage is built up. Revision 1.0 (5cm) VDD3 V3 4k7 PRO CSN 6 µC SDA 5 SCL 4 5VUSB 3 VDD3V3 2 VSS VOUT_EX www.austriamicrosystems.com connect to USB interface on PC VPRO 3 7.5 … 8.0V G only required 2 + for 10µ 1 OTP F programming VSS GN D Page ...
Page 11
... It is possible to write "1"s into the OTP register at subsequent programming cycles. However, a programmed "1" cannot be cleared any more after programming. Note that the chip will not be programmed, as long as no programming voltage is applied to Vzapp, although the software will issue a warning message that the chip will be permanently programmed. Revision 1.0 www.austriamicrosystems.com Page ...
Page 12
... No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems rendering of technical or other services. ...