DV164036 Microchip Technology, DV164036 Datasheet - Page 15

• Manufacturer Part Number: DV164036
• Description: KIT EVAL ICD3 WITH PICDEM 2 PLUS
• Manufacturer: Microchip Technology
• Series: MPLAB® ICD 3r
• Type: MCUr

Specifications of DV164036

• Contents: Board, CD, ICD3 Debugger, Power Supply
• Processor To Be Evaluated: PIC16, PIC18
• Data Bus Width: 8 bit
• Interface Type: RS-232, USB
• Operating Supply Voltage: 5 V
• Silicon Manufacturer: Microchip
• Core Architecture: PIC
• Core Sub-architecture: PIC16, PIC18
• Silicon Core Number: PIC16F, PIC18F
• Silicon Family Name: PIC16F8xxx, PIC18F4xxx
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: Microchip 8-Bit PICmicro™ Microcontrollers
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

2.1
© 2007 Microchip Technology Inc.
PICDEM™ 2 PLUS AS A STAND-ALONE BOARD –
PREPROGRAMMED DEVICE
The PICDEM 2 Plus may be used as a stand-alone board with a preprogrammed
device, with an In-Circuit Emulator (ICE) or with an In-Circuit Debugger (ICD). For a list
of PIC
Ordering Guide.
The PICDEM 2 Plus may be demonstrated immediately by following the steps listed
below:
• Place the preprogrammed sample device in the appropriate socket on the
• Place a jumper on J6 (to enable the LEDs).
• Verify that the board is set up for a 4 MHz, canned oscillator (that is, no jumper on
• Apply power to the PICDEM 2 Plus. For information on acceptable power sources,
To reprogram the sample device, the following will be necessary:
• Program source code – user source code may be used to program the device, or
• An assembler, such as MPASM™ assembler (available with MPLAB
PICDEM 2 Plus demonstration board.
J7; a 4 MHz oscillator in Y2 and nothing in Y1, C4 and C5).
see Appendix A.
if this previously has been done, the sample program may be restored from the
file on the included CD-ROM.
compiler, such as MPLAB C18 (PIC18 devices only)
Source code must be assembled or compiled into a hex file before it can be pro-
grammed into the device. Microchip Technology’s MPASM assembler or MPLAB
C18 C compiler may be used. Both are compatible with MPLAB IDE.
Other assemblers/compilers may be used. For a list of these PIC MCU compatible
language tools, see the Microchip web site (www.microcip.com).
A device programmer, such as PRO MATE
or MPLAB ICD 2 (programmer functionality available with MPLAB IDE v6.00 or
greater)
Once the sample program is in hex file format, a programmer can program a
Flash device. Microchip Technology’s PRO MATE II device programmer,
PICSTART Plus development programmer or MPLAB ICD 2 may be used. All are
compatible with MPLAB IDE.
Other programmers may be used. For a list of these PICmicro MCU compatible
programmers, see the Microchip web site (www.microcip.com).
If the code protection bit(s) have not been programmed, the on-chip program
memory can be read out for verification purposes.
®
microcontroller compatible ICEs or ICDs, see the Development Systems
Chapter 2. Getting Started
PICDEM™ 2 PLUS USER’S GUIDE
®
II, MPLAB
®
PM3, PICSTART
DS51275D-page 11
®
IDE), or a
®
Plus