Z8F64200100KIT Zilog, Z8F64200100KIT Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/7/729/zilog_sml.jpg)
Z8F64200100KIT
Manufacturer Part Number
Z8F64200100KIT
Description
DEV KIT FOR Z8 ENCORE 16K TO 64K
Manufacturer
Zilog
Series
Z8 Encore!®r
Type
MCUr
Datasheets
1.Z8F64200100KITG.pdf
(18 pages)
2.Z8F64200100KITG.pdf
(9 pages)
3.Z8F64200100KIT.pdf
(17 pages)
Specifications of Z8F64200100KIT
Contents
Evaluation Board, Cable, Power Supply, Software and Documentation
Processor To Be Evaluated
Z8F642
Data Bus Width
8 bit
Interface Type
I2C, UART
For Use With/related Products
Z8 Encore!™
For Use With
269-4661 - KIT ACC ETHERNET SMART CABLE
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
269-3249
Loader project settings and
Application Code Generation
code relocation.
The user can move from USER APPLICATION
mode to FLASH LOADER mode by pressing the
special sequence key and pressing the Reset button
on the evaluation board.
Flash Loader
The Flash Loader features the following layers for
implementing code:
Startup Code
This piece of code is the default code used to bring
the device to a known state, then relinquish control
over to the start of the main program.
Serial Port Initialization
This layer initializes the serial port (the console port)
for the Flash Loader.
Flash Read/Write Utilities
This layer provides basic Flash and RAM Read/Write
capabilities and constitutes the core layer of the Flash
Loader utility.
File Parser, Error Checker, and Flash
Loader
This layer receives the Intel Hex file frame by frame,
checks each frame, and processes each frame
according to its type. The frame start address is
derived and the frame data is directly programmed
into Flash.
User Interface Layer
This layer provides for user interaction with the Flash
Loader via HyperTerminal. Because this layer uses
standard libraries such as
constitutes the bulk of the Flash Loader code.
AN011806-0408
printf
Appendix B—User
on page 13 for user
and
scanf
, it
Flash Loader Utility for the Z8 Encore! XP
The Flash Loader uses UART0 to communicate via
HyperTerminal console and works with the
following default configurations:
•
•
•
•
The console port can be extended to a peripheral such
as UART1, I
words, Z8 Encore! XP MCU Flash memory can be
programmed remotely using a modem or by an IrDA
device (for example, a Palm Pilot) that beams its
signal.
Table 1
application code and the Flash Loader reside on the
Z8 Encore! XP F64XX Series MCU.
Table 1. Flash Loader/User Application Memory
Map
Flash Loader starts on a fresh 512 byte boundary, that
is, address
area occupies the address range
boundary at
1FFh
See
Flash Loader project settings and
User Application Code Generation
user code relocation.
Memory Location
0000h-0001h
0002h-0007h
0008h-0037h
0038h-01FFh
0200h-3FFFh
4000h-FFFFh
UART0 (console port on the Z8 Encore! XP
Evaluation Board)
9600 bps
8-N-1
Flow Control = none
Appendix A—Project Settings
is assumed to be reserved by the Flash Loader.
lists the memory locations in which user
200h
FFFFh
2
C, GPIO, Modem, or IrDA. In other
and above. The application code
. The Flash address range
Description
Flash Option Bits
Reset/WDT/Trap Vectors
Interrupt Vectors
Reserved
Flash Loader
User application code
4000h
Appendix B—
on page 10 for
on page 13 for
Page 3 of 17
to the 64 K
®
MCU
38h–