C8051F320-TB Silicon Laboratories Inc, C8051F320-TB Datasheet
C8051F320-TB
Specifications of C8051F320-TB
Related parts for C8051F320-TB
C8051F320-TB Summary of contents
Page 1
... Kit Contents The C8051F32x Development Kit contains the following items: • C8051F320 Target Board • C8051Fxxx Development Kit Quick-Start Guide • Silicon Laboratories IDE and Product Information CD-ROM. CD content includes: • Silicon Laboratories Integrated Development Environment (IDE) • Keil 8051 Development Tools (macro assembler, linker, evaluation ‘C’ compiler) • ...
Page 2
C8051F32x-DK 3. Software Setup The included CD-ROM contains the Silicon Laboratories Integrated Development Environment (IDE), Keil software 8051 tools and additional documentation. Insert the CD-ROM into your PC’s CD-ROM drive. An installer will automatically launch, allowing you to install the ...
Page 3
Creating a New Project → 1. Select Project New Project to open a new project and reset all configuration settings to default. → 2. Select File New File to open an editor window. Create your source file(s) and save ...
Page 4
... The included USB application example requires Windows 98SE/2000/XP operating system. This example consists of three parts, firmware running on the C8051F320 device, a USB device driver running on the host PC, and a host application. The host application communicates with the C8051F320 via USB, allowing the user to view and to change the state of several I/O peripherals on the C8051F320 target board. The example files can be found in the “ ...
Page 5
... J10 (P0.3) and J13 (P1.7 Potentiometer). 5. See Figure 2 on page 6 for the location of headers, LEDs, switches, and potentiometer. Note: The C8051F320 target board has the ability to be powered through the USB cable. To enable the USB powered mode, move the shorting block located at header J2 to header J11. ...
Page 6
... C8051F32x-DK 6. Target Board The C8051F32x Development Kit includes a target board with a C8051F320 device pre-installed for evaluation and preliminary software development. Numerous input/output (I/O) connections are provided to facilitate prototyping using the target board. Refer to Figure 2 for the locations of the various I/O connectors. ...
Page 7
... Switches and LEDs Three switches are provided on the target board. Switch SW1 is connected to the RESET pin of the C8051F320. Pressing SW1 puts the device into its hardware-reset state. Switch SW2 and SW3 are connected to the C8051F320’s general purpose I/O (GPIO) pins through headers. Pressing SW2 or SW3 generates a logic low signal on the port pin ...
Page 8
... Table 2. USB Connector Pin Descriptions 6.4. Expansion I/O Connector (J1) The 32-pin Expansion I/O connector J1 provides access to all signal pins of the C8051F320 device. Pins for +3 V, digital ground and the output of an on-board low-pass filter are also available. A small through-hole prototyping area is also provided. All I/O signals routed to connector J1 are also routed to through-hole connection points between J1 and the prototyping area (see Figure 2 on page 6) ...
Page 9
... J3[13-14] - Install shorting block to connect UART0 RTS (P2.6) to transceiver. J3[15-16] - Install shorting block to connect UART0 CTS (P2.7) to transceiver. 6.8. Analog I/O (J6) Several of the C8051F320 target device’s port pins are connected to the J6 terminal block. Refer to Table 5 for the J6 terminal block connections. Table 5. J6 Terminal Block Pin Descriptions 6 ...
Page 10
C8051F32x-DK 7. Schematic 10 Rev. 0.8 ...
Page 11
OCUMENT HANGE IST Revision 0.6 to Revision 0.7 Section 1, added USB Debug Adapter and USB Cable. Section 2, changed name from "Hardware Setup" to "Hardware Setup using an EC2 Serial Adapter". Section 2, added 2 Notes ...
Page 12
... Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized ap- plication, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders. ...