EVAL-AD7714-3EB Analog Devices Inc, EVAL-AD7714-3EB Datasheet - Page 32
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
EVAL-AD7714-3EB
Manufacturer Part Number
EVAL-AD7714-3EB
Description
BOARD EVAL FOR AD7714-3
Manufacturer
Analog Devices Inc
Datasheet
1.AD7714YNZ.pdf
(40 pages)
Specifications of EVAL-AD7714-3EB
Rohs Status
RoHS non-compliant
Number Of Adc's
1
Number Of Bits
24
Sampling Rate (per Second)
1k
Data Interface
Serial
Inputs Per Adc
3 Differential
Input Range
0 ~ 3.3 V
Power (typ) @ Conditions
3.65mW @ 3.3 V
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
AD7714-3
AD7714
interfaces which require control of the CS input on the AD7714,
one of the port bits of the 8XC51 (such as P1.1), which is con-
figured as an output, can be used to drive the CS input.
The 8XC51 is configured in its Mode 0 serial interface mode.
Its serial interface contains a single data line. As a result, the
DATA OUT and DATA IN pins of the AD7714 should be
connected together. The serial clock on the 8XC51 idles high
between data transfers and, therefore, the POL input of the
AD7714 should be hard-wired to a logic high. The 8XC51
outputs the LSB first in a write operation while the AD7714
expects the MSB first so the data to be transmitted has to be
rearranged before being written to the output serial register.
Similarly, the AD7714 outputs the MSB first during a read
operation while the 8XC51 expects the LSB first. Therefore, the
data that is read into the serial buffer needs to be rearranged
before the correct data word from the AD7714 is available in
the accumulator.
AD7714 to ADSP-2103/ADSP-2105 Interface
Figure 11 shows an interface between the AD7714 and the
ADSP-2103/ADSP-2105 DSP processor. In the interface shown,
the DRDY bit of the Communications Register is again moni-
tored to determine when the Data Register is updated. The
alternative scheme is to use an interrupt driven system in which
case, the DRDY output is connected to the IRQ2 input of the
ADSP-2103/ADSP-2105. The RFS and TFS pins of the
ADSP-2103/ADSP-2105 are configured as active low outputs
and the ADSP-2103/ADSP-2105 serial clock line, SCLK, is
also configured as an output. The POL pin of the AD7714 is
hard-wired low. Because the SCLK from the ADSP-2103/
ADSP-2105 is a continuous clock, the CS of the AD7714 must
be used to gate off the clock once the transfer is complete. The
CS for the AD7714 is active when either the RFS or TFS
8XC51
Figure 10. AD7714 to 8051 Interface
P3.0
P3.1
DV
DD
SYNC
POL
DATA IN
RESET
DATA OUT
SCLK
CS
AD7714
–32–
outputs from the ADSP-2103/ADSP-2105 are active. The serial
clock rate on the ADSP-2103/ADSP-2105 should be limited to
3 MHz to ensure correct operation with the AD7714.
CODE FOR SETTING UP THE AD7714
Table XV gives a set of read and write routines in C code for
interfacing the 68HC11 microcontroller to the AD7714. The
sample program sets up the various registers on the AD7714
and reads 1000 samples from the part into the 68HC11. The
setup conditions on the part are exactly the same as those out-
lined for the flowchart of Figure 8. In the example code given
here the DRDY output is polled to determine if a new valid
word is available in the output register.
The sequence of the events in this program are as follows:
1. Write to the Communications Register, setting the channel.
2. Write to the Filter High Register, setting the 4 MSBs of the
3. Write to the Filter Low Register, setting the 8 LSBs of the
4. Write to the Mode Register, setting the part for a gain of 1,
5. Poll the DRDY Output.
6. Read the data from the Data Register.
7. Loop around doing steps 5 and 6 until the specified number
Figure 11. AD7714 to ADSP-2103/ADSP-2105 Interface
filter word and setting the part for 24-bit read, bipolar mode
with boost off.
filter word.
burnout current off, no filter synchronization and initiating a
self-calibration.
of samples have been taken.
ADSP-2103/2105
SCLK
RFS
TFS
DR
DT
DV
DD
RESET
SYNC
CS
DATA OUT
DATA IN
SCLK
POL
AD7714
REV. C