KS8993-EVAL Micrel Inc, KS8993-EVAL Datasheet - Page 13

• Manufacturer Part Number: KS8993-EVAL
• Description: BOARD EVAL EXPERIMENT FOR KS8993
• Manufacturer: Micrel Inc

Specifications of KS8993-EVAL

• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 576-1011

May 2005
KS8993
Group
P[3:1]_TAGINS
P[3:1]_TAGRM
P[3:1]_1PEN
P[3:1]_TXQ2
PBASE[2:0]
I/O Names
P[3:1]_PP
VMDIS
PRSV
PV12
PV13
PV21
PV23
PV31
PV32
Active Status
H
H
H
H
H
H
H
H
H
Description
VLAN Mismatch Discard control.
Pulled low = Constrict multicast and broadcast packets to VLAN.
Pulled high = Constrict all packets to VLAN (default).
Reserve priority buffers.
Pulled low = No buffers reserved (default).
Pulled high = Reserve 96 buffers per port for high priority queue.
Priority base value used to compare with priority tag in 802.1p tag. When a packet is
received that has a 802.1p tag and 802.1p processing is enabled (Px_1PEN=H), the
PBASE value is compared to the tag priority field. If the packet tag is greater than or
equal to the PBASE value, the packet is sent to the higher priority transmit queue
while tags less than PBASE are sent to the lower priority queue. (default = 100).
VLAN mask bits. Used to select which ports are seen from any particular port. Use
the table below to select VLAN operation.
P1_V defined as (PV13, PV12, 1)
P2_V defined as (PV23, 1 , PV21)
P3_V defined as (1 , PV32, PV31)
P[3:1]_V
Port
1
2
3
Note that a minimum of 2 ports are required for each VLAN. The VLAN configuration
is viewed from the receiver perspective. All states not listed above are invalid.
Enables 802.1p prioritizing on a per port basis. The enable is from the receive
perspective. If the 802.1p processing is disabled or there is no tag, priority is dete-
mined by the P[3:1]_PP bit.
Pulled low = Disable 802.1p prioritizing (default).
Pulled high = Enable 802.1p prioritizing.
Selects port receive priority in the absence of 802.1p handling.
Pulled low = Low priority (default).
Pulled high = High priority.
Inserts 802.1p tag in received packets if not already existent. The priority field is set
based on the port P[3:1]_PP bit. For the P[3:1]_PP bit tied low, the priority field is set
to 000 and for the P[3:1]_PP bit tied high, the priority field is set to 111.
Pulled low = No change to received packet (default).
Pulled high = Insert 802.1p tag.
Note that if P[3:1]_TAGINS and P[3:1]_TAGRM are both set for the same port, there
is no change to the packet.
Removes 802.1p tag in received packets if they exist.
Pulled low = No change to received packet (default).
Pulled high = Remove 802.1p tag.
Note that if P[3:1]_TAGINS and P[3:1]_TAGRM are both set for the same port, there
is no change to the packet.
Selects transmit queue split on a per port basis. The split sets up high and low priority
queues.
Pulled low = Single transmit queue (default)
Pulled high = Separate high and low transmit queues
2
0
1
1
0
1
1
1
1
1
13
1
1
0
1
1
1
1
0
1
1
0
1
1
1
1
0
1
1
0
1
VLAN State
Ports 1 and 2 in VLAN
Ports 1 and 3 in VLAN
Ports 1, 2 and 3 in VLAN (default)
Ports 1 and 2 in VLAN
Ports 2 and 3 in VLAN
Ports 1, 2 and 3 in VLAN (default)
Ports 1 and 3 in VLAN
Ports 2 and 3 in VLAN
Ports 1, 2 and 3 in VLAN (default)
KS8993
Micrel