G6C-2117P-US-DC8 Omron, G6C-2117P-US-DC8 Datasheet - Page 4

• Manufacturer Part Number: G6C-2117P-US-DC8
• Description: POWER PCB RELAY
• Manufacturer: Omron
• Series: G6Cr

Specifications of G6C-2117P-US-DC8

• Relay Type: General Purpose
• Contact Form: DPST-NO/NC (1 Form A and B)
• Contact Rating (current): 8A
• Switching Voltage: 380VAC, 125VDC - Max
• Coil Type: Standard
• Coil Current: 25mA
• Coil Voltage: 8VDC
• Turn On Voltage (max): 5.6 VDC
• Turn Off Voltage (min): 0.8 VDC
• Mounting Type: Through Hole
• Termination Style: PC Pin
• Circuit: DPST-NO/NC (1 Form A and B)
• Contact Rating @ Voltage: 8A @ 250VAC
• Control On Voltage (max): 5.6 VDC
• Control Off Voltage (min): 0.8 VDC
• Coil Voltage Vdc Nom: 8V
• Contact Current Max: 8A
• Contact Voltage Ac Nom: 250V
• Contact Voltage Dc Nom: 30V
• Coil Resistance: 720ohm
• Contact Configuration: SPST-NO / SPST-NC
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: G6C2117PUSDC8

5.12 Ｔerminal strength
5.13 Ｔemperature resistance
5.14 Ｍoisture resistance
5.15 Ｓoldering heat
5.16 Ｅndurance
(2)Ｍalfunction durability
※Unless otherwise specified, the above mentioned item 4 (Ratings) and
(1)Ｍechanical endurance
(2)Ｅlectrical endurance
(1) Ｈeat resistance
(2) Ｃold resistance
5 (Characteristics) values are under the standard conditions of
Ambient temperature 23℃ and Humidity 65%RH.
（Ｗhen not energized）
resistance
（Ｗhen energized）
or set status
or reset status
（under no load at operating frequency of
（under rated load, at operating frequency of
Ｃontacts must not open for１ms
or longer after the relay is subjected to a
shock of １００ m/s
３times.
Ｃontacts must not open for１ms or
longer after the relay is subjected to a shock
of １００m/s
３times.
Ｍust be free from any abnormality after
a tensile stress of ９.８Ｎ is applied to the
terminal in any direction vertical to the
terminal tip for １０ seconds.
Ａny deformation of the terminal by the load
shall not be regard as a mechanical damage.
Ｍust be free from any abnormality in both the
construction and characteristics after the
relay is left in a temperature of ８５±２℃
for 16 hours and then in room temperature and
humidity for ２ hours.
Ｍust be free from any abnormality in both the
construction and characteristics after the
relay is left in a temperature of －５５±３ ℃
for 72 hours and then in room temperature and
humidity for ２ hours.
Ｍust be free from any abnormality in both the
construction and characteristics after the
relay is left in a humidity of 90 to 95% ＲＨ
for 48 hours at a temperature of 40±2℃, and
then in room temperature and humidity for
2 hours.
Insulation resistance, however,
must be ５ ＭΩ MIN.
Ｍust be free from any abnormality in both
the construction and characteristics after
the terminals are dipped into molten solder
at ２６０±５℃ for １０±１ seconds and then
left in room temperature and humidity for
2 hours.
50,000,000 operations MIN.
18,000 operations／hour）
100,000 operations MIN.
1,800 operations／hour）
in each direction
in each direction
Spec No：G6C-0705007A
P. 4