1100210000 Weidmuller, 1100210000 Datasheet - Page 64
![no-image](/images/manufacturer_photos/0/7/707/weidmuller_sml.jpg)
1100210000
Manufacturer Part Number
1100210000
Description
RELAY DSCRETE 24VDC SPDT GN LED
Manufacturer
Weidmuller
Specifications of 1100210000
Relay Type
General Purpose
Contact Form
SPDT (1 Form C)
Contact Rating (current)
6A
Switching Voltage
250VAC
Coil Type
Standard
Coil Voltage
24VDC
Mounting Type
DIN Rail
Termination Style
Screw Terminal
Circuit
SPDT (1 Form C)
Contact Rating @ Voltage
6A @ 250VAC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Coil Current
-
Control On Voltage (max)
-
Control Off Voltage (min)
-
Other names
RS 30 24VDC SPDT GRN
Opto-couplers DKO
S0 signal sensor
Application example:
Signals for consumers are normally transferred
via an interface. Generally, this interface must
conform with DIN 43867 (interface for signal
transmission). There must be a differentiation
between the passive interface and active S0
interface. The actual signals, that are corres-
pondingly proportional to the relevant con-
sumption (electrical energy, gas consumption,
water, district heating, etc.) are shown at
measuring sensors (electric meter, etc.) The
interface itself is purely passive (acceptor) and
must be supplied via a source. The source for
providing the current is built into the active
interface. The following threshold values are
specified:
For the recognition of the corresponding con-
sumption signals, the following currents are
integrated:
The module accepts the input from the signal
sensor and outputs the opto-decoupled output
signal, i. e. galvanically isolated.
For TS 32
For TS 35
With combination foot TS 32 / TS 35
Input
Input voltage
Input current
Pulse generator
Output
Output voltage
Output current
Voltage proof input-output/mounting rail
Rated voltage
Rated impulse voltage
Overvoltage category
Pollution severity
Clearances and creepage distances
Operating temperature
Storage temperature
Conductor
Conductor cross-section
Overall width
End plate
Ordering data
Technical data
Insulation coordination to DIN VDE 0160, Draft 11/94
Accessories
Opto-coupler in component housing mini coupler DK
I
U
f
ON (active) -> 10…27 mA
Off (inactive) -> 0…2 mA
max
max
max
= 27 mAdc
= 16.66 Hz
= 27 Vdc
without clearances
with clearances
W
Y
DKO switching amplifiers/opto-couplers for Namur initiators
DKO DK4 S0
DKO DK4 S0
DKO DK4 S0
24 Vdc ±10 %
≤13 mA
Specification acc. to DIN
43864 (current interface for
connection to pulse generator
acc. to DIN 43864)
5…48 Vdc
max. 100 mA
4 kV
300 V
6 kV
IV
2
≥5.5 mm
-25 °C…+40 °C
-25 °C…+50 °C
-40 °C…+60 °C
AWG 22…12
0.5…4 mm
12 mm
AP DKT4
Schematic circuit diagram
Type
Type
eff
2
Cat. No.
8467030000
8100180000
Cat. No.
0687560000
For TS 32
For TS 35
With combination foot TS 32 / TS 35
Input
Input voltage
Input current
Reverse polarity protection
NAMUR-Input (N+ and N-)
Switching frequency
Switch-on delay
Switch-off delay
Input (E+ and 0)
Switch-on point
Switch off-point
Current consumption
Max. switching frequency
Switch-on delay
Switch-off delay
Output (A+ and A-)
Output voltage
Output current
Switching capacity
Internal voltage drop
Protective measure
Voltage proof input-output/mounting rail
Operating temperature
Storage temperature
Conductor
Conductor cross-section
Overall width
End plate
Ordering data
Technical data
Accessories
W
without clearances
with clearances
W
Y
DKO
24 Vdc ±20 %
≤35 mA
up to 1 kV available
300 Hz f. pulse duty factor 1:1
approx.45 µs
approx.450 µs
approx.18 V
ca 15 V
< 5 mA
300 Hz f. pulse duty factor 1:1
approx.20µs
approx.400 µs
5…30 Vdc
max. 100 mA
max. 3 W
max. 1 V
Free-wheel. diode btwn. A+…A-
4 kV
-25 °C…+40 °C
-25 °C…+50 °C
-40 °C…+60 °C
AWG 22…12
0.5…4 mm
12 mm
AP DKT4
DKO
Schematic circuit diagram
Type
Type
eff
2
Cat. No.
8164250000
Cat. No.
0687560000
121