G6K-2F-Y DC4.5 Omron, G6K-2F-Y DC4.5 Datasheet - Page 9

• Manufacturer Part Number: G6K-2F-Y DC4.5
• Description: RELAY SMT DPDT 1A 4.5V GULLWING
• Manufacturer: Omron
• Series: G6Kr
• Type: Signal Relayr

Specifications of G6K-2F-Y DC4.5

• Relay Type: Telecom
• Circuit: DPDT (2 Form C)
• Contact Rating @ Voltage: 1A @ 30VDC
• Coil Type: Standard
• Coil Current: 23.2mA
• Coil Voltage: 4.5VDC
• Control On Voltage (max): 3.6 VDC
• Control Off Voltage (min): 0.45 VDC
• Mounting Type: Surface Mount
• Termination Style: Gull Wing
• Contact Form: DPDT
• Current, Rating: 0.3⁄1 AAC⁄ADC
• Function: Sensitive
• Number Of Pins: 8
• Power, Rating: 37.5⁄30 VA⁄W
• Standards: UL, CSA, RoHS
• Termination: Surface Mount
• Voltage, Control: 4.5 VDC
• Voltage, Rating: 125 VAC
• Relay Construction: Non-Latching
• Contact Arrangement: DPDT
• Coil Voltage Dc: 4.5V
• Voltage Rating (vdc): 60V
• Voltage Rating (vac): 125V
• Dropout Volt (min): 0.45VDCV
• Coil Resistance: 194Ohm
• Pick-up Voltage (max): 3.6VDC
• Maximum Power Rating: 30W/37.5VA
• Operate Time: 3ms
• Contact Current Rating: 1A
• Contact Material: Ag/Au
• Coil Suppression Diode: No
• Push To Test Button: No
• Led Indicator: No
• Seal: Unsealed
• Product Height (mm): 5.2mm
• Product Depth (mm): 7.8mm
• Product Length (mm): 10mm
• Operating Temp Range: -40C to 70C
• Pin Count: 8
• Mounting Style: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: G6K-2F-Y-DC4.5; G6K2FYDC4.5; G6K2FYDC45; Z127

• Must not cause thermal changes in or deterioration of the insulating
• Must not cause damage to other control devices.
• Must not cause any harmful effect on people.
• Must not cause fire.
Therefore, be sure to use the maximum allowable voltage as speci-
fied in the catalog.
As a rule, the rated voltage must be applied to the coil. A voltage
exceeding the rated value, however, can be applied to the coil pro-
vided that the voltage is less than or equal to the maximum allowable
voltage. It must be noted that continuous voltage application to the
coil will cause a coil temperature increase which may affect charac-
teristics such as electrical life and coil insulation.
Coating
The Relay mounting on the PCB may be coated or washed but do not
apply silicone coating or detergent containing silicone, otherwise the
silicone coating or detergent may remain on the surface of the Relay.
PCB Mounting
If two or more Relays are closely mounted with the long sides of the
Relays facing each other and soldering is performed with infrared
radiation, the solder may not be properly exposed to the infrared
rays. Be sure to keep the proper distance between adjacent Relays
as shown below to insure formation of good solder joints.
Two or more Relays may be mounted as closely as desired with the
short sides of the Relays facing each other.
material.
G6K-2G
G6K-2F
2 mm min.
2.7 mm min.
Low Signal Relay
G6K
75