ARE13A4H Panasonic Electric Works, ARE13A4H Datasheet - Page 5

• Manufacturer Part Number: ARE13A4H
• Description: RELAY 2.6GHZ .50A 4.5VDC SMD
• Manufacturer: Panasonic Electric Works
• Series: AREr

Specifications of ARE13A4H

• Relay Type: RF
• Circuit: SPDT (1 Form C)
• Contact Rating @ Voltage: 0.5A @ 30VDC
• Coil Type: Standard
• Coil Current: 44.4mA
• Coil Voltage: 4.5VDC
• Control On Voltage (max): 3.38 VDC
• Control Off Voltage (min): 0.45 VDC
• Mounting Type: Surface Mount
• Termination Style: Gull Wing
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 255-1575; 255-1575-5; 255-1575

RE (ARE)
• 75Ω type
Note: Please consult us regarding recommended PC board patterns.
NOTES
1. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be
rectangular. If it includes ripple, the ripple
factor should be less than 5%.
However, check it with the actual circuit
since the characteristics may be slightly
different.
2. Cleaning
For automatic cleaning, the boiling
method is recommended. Avoid
ultrasonic cleaning which subjects the
relays to high frequency vibrations, which
may cause the contacts to stick.
It is recommended that alcoholic solvents
be used.
3. Soldering
(Standard PC board terminal)
1) The manual soldering shall be
performed under following condition.
Max. 260°C
Max. 350°C
The affect of the PCB on the relay will
differ depending on the type of PCB
used. Please verify the type of PCB to be
used.
Preheat according to the following
conditions.
Soldering should be done at 260±5°C
500±9°F
2) In case of automatic soldering, the
following conditions should be observed
(Surface-mount terminal)
(1) Position of measuring temperature
CAD Data
Temperature
A: Surface of PC board where relay is mounted.
Time
within 6 s.
500°F
662°F
10s
3s
120°C
Within 2 minute
248°F
13.2
.520
A
±0.5
±.020
or less
(.511)
(.028)
(0.7)
(1.3)
.339
11.2
.441
.012
8.6
0.3
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
2.54
.100
20.2
.795
(2) IR (infrared reflow) soldering method
Temperature rise of relay itself may vary
according to the mounting level or the
heating method of reflow equipment.
Therefore, please set the temperature of
soldering portion of relay terminal and
the top surface of the relay case not to
exceed the above mentioned soldering
condition.
It is recommended to check the
temperature rise of each portion under
actual mounting condition before use.
4. Packing style
1) Tape dimensions
2) Dimensions of plastic reel
5. Conditions for operation, transport
and storage conditions
1) Ambient temperature, humidity, and
atmospheric pressure during usage,
transport, and storage of the relay:
R0.75
T
T
.079
.030
3
1
2.0
Relay polarity bar
.067
1.7
1.5
±.020
±0.5
.020
0.5
.059
Tape coming out direction
1.5
+0.1
−0
General tolerance: ±0.3
.059
RE Relay
+.004
−0
.012
(1.49)
(.059)
0.3
t
T
1
dia.
2
.157
20.0
.787
4
7.62
.300
21
.827
2.0
.079
t
13
.512
2
±0.8
Max. 51.7
±0.2
1.791
±0.15
±.031
±.006
45.5
dia.
Max. 95
±.008
dia.
2.035
20.75
13.85
.545
.817
dia.
3.740
(2.09)
(.082)
.012
dia.
+0.2
−0
+.008
−0
0.3
T
T
T
1.75
.069
20.2
.795
t
t
1
2
1
2
3
=
=
=
=
=
1.591
40.4
155 to 165°C
311 to 329°F
180 to 200°C
356 to 392°F
245°C max.
473°F max.
within 120s
within 30s
9.6
.378
±.012
44
1.732
±0.3
.016
380
14.961
0.4
±.012
10.6
.417
±0.2
±.008
+0.2
−0.3
+.008
−.012
(Deenergized condition)
(1) Temperature:
–40 to +70°C
(2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range
indicated in the graph below.
(3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for
usage, transport, and storage:
2) Condensation
Condensation forms when there is a
sudden change in temperature under
high temperature and high humidity
conditions. Condensation will cause
deterioration of the relay insulation.
3) Freezing
Condensation or other moisture may
freeze on the relay when the temperature
is lower than 0°C 32°F. This causes
problems such as sticking of movable
parts or operational time lags.
4) Low temperature, low humidity
environments
The plastic becomes brittle if the relay is
exposed to a low temperature, low
humidity environment for long periods of
time.
For general cautions for use, please
refer to the “General Application
Guidelines”.
(Avoid freezing
when used at
temperatures lower
than 0°C
Direction indication
–40
–40
32°F
Tolerance range
Schematic (Top view)
Temperature, °C
–40 to +158°F
85
5
+32
0
(Avoid
condensation
when used at
temperatures higher
than 0°C
Humidity, %RH
NC
1
14
32°F
13
°F
COM
12
11 10 9
+158
70
NO
7
8