G3NA-225B DC5-24 Omron, G3NA-225B DC5-24 Datasheet - Page 15
![RELAY SSR 120VAC@25A ZERO DC IN](/photos/9/55/95585/g3na-_relay_series_sml.jpg)
G3NA-225B DC5-24
Manufacturer Part Number
G3NA-225B DC5-24
Description
RELAY SSR 120VAC@25A ZERO DC IN
Manufacturer
Omron
Series
G3NAr
Datasheets
1.G3NA-225B_DC5-24.pdf
(18 pages)
2.G3NA-240B-AC100-120.pdf
(17 pages)
3.G3NA-225B_DC5-24.pdf
(9 pages)
Specifications of G3NA-225B DC5-24
Load Current
25A
Circuit
SPST-NO (1 Form A)
Output Type
AC, Zero Cross
Voltage - Input
5 ~ 24VDC
Voltage - Load
19 ~ 264 V
Mounting Type
Chassis Mount
Termination Style
Screw Terminal
Package / Case
Hockey Puck
Control Voltage Range
5VDC To 24VDC
Operating Voltage Range
19VAC To 264VAC
Isolation Voltage
2500VAC
Control Voltage Type
DC
Relay Terminals
Screw
Load Voltage Max
240VAC
Load Voltage Min
24VAC
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
On-state Resistance
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
G3NA-225B-DC5-24
G3NA225BDC524
Z921
G3NA225BDC524
Z921
Preventing Overheating with a High-
capacity Heat Sink (Y92B-P250NF)
• When the High-capacity Heat Sink is used, high-capacity switching
• If the Fan stops due to a power supply error, due to foreign matter
• A thermostat is provided to detect overheating. The thermostat
• Do not connect the thermostat directly to the load power supply.
• Terminals equivalent to Faston #187 are used for the thermostat
• Do not place heat-dissipating silicon grease on the thermostat.
• Do not solder the thermostat terminals.
• The following diagram shows a protective circuit example.
Ventilating a High-capacity Heat Sink
(Y92B-P250NF)
• Refer to Ventilation Outside the Control Panel.
Operating Conditions
• Do not apply currents exceeding the rated current otherwise, the
• As protection against accidents due to short-circuiting, be sure to
• Do not apply overvoltages to the input circuit or output circuit.
• Do not drop the G3NA or otherwise subject it to abnormal shock.
• Keep the cooling system running continuously during the ON/OFF
EMC Directive Compliance (For -UTU type)
EMC directives can be complied with under the following conditions.
1. AC-switching models
• A capacitor must be connected to the input power supply.
• A capacitor, varistor and toroidal core must be connected to the
• The input cable must be less than 3 m.
Coil
power
supply
at 75 A or 90 A requires forced cooling with a fan. Connect the Fan
to a power supply according to its ratings specifications.
in the power supply connection, or due to aging, the Heat Sink will
heat to high temperatures, possibly resulting in failure of the SSR or
adverse affects on other devices. Implement an overheating
prevention measure, such as turning OFF the load current, if the
Heat Sink overheats.
uses a NC contact, i.e., the circuit will be opened for overheating.
This thermostat can be used to stop the operation of the SSR.
Implement an overheating prevention measure by using this signal
to output an alarm or perform another response applicable to the
system. Also, confirm that there is no problem with the overall
system.
Connect it to a contactor or other shutoff device connected above
the SSR.
terminals.
temperature of the G3NA may rise excessively.
install protective devices, such as fuses and no-fuse breakers, on
the power supply side.
Failure or burning may result.
Malfunction or failure may result.
operation of the SSR. This is to allow residual heat to dissipate
while the SSR is OFF. (load current 75 A, 90 A models)
load power supply.
Input side
Circuit breaker
(coil side)
3 m max.
Input
Recommended Capacitor : 0.05µF, 500 VAC (Load)
Recommended Varistor : 470 V, 1750 A
Recommended Troidal core : NEC/TOKIN:ESD-R-25B or equivalent
(NC contact)
Thermostat
G3NA
Y92B-P250NF
G3NA
Output
Troidal core
Load
0.1µF, 250 VAC (Input)
Load side
Load
Circuit breaker
(contact side)
Circuit
breaker
2. DC-switching models
• The input cable must be less than 3 m.
Loss Time
The loss time will increase when the G3NA is used at a low applied
voltage or current. Be sure that this does not cause any problems.
Using DC Loads
For a DC or L load, a diode should be connected in parallel the load
to absorb the counter electromotive force of the load.
Fuses
Connect a quick-break fuse in series with the load as a short-circuit
protection measure. Use one of the fuses in the following table or
one with equivalent or better characteristics.
Recommended Fuses
Reverse Connection
The output terminal side of the G3NA-D210B is connected to a built-
in diode to protect the SSR from damage that may result from
reverse connection. The SSR, however, cannot withstand one minute
or more if the wires are connected in reverse. Therefore, pay the
utmost attention not to make polarity mistakes on the load side.
5 A
8 A
10 A
15 A
20 A
25 A
30 A
40 A
45 A
50 A
75 A
80 A
100 A
load current
G3NA rated
Input
Less than 3 m
Input G3NA-UTU
60LFF5
60LFF8
60LFF10
60LFF15
60LFF20
50SHA20
60PFF25
50SHA25
60PFF30
50SHA30
50SHA40
50SHA45
50SHA50
50SHA75
50SHA80
50SHB100
Fuse model
SSR
Loss time
Output
HINODE ELECTRIC
CO.,LTD.
Manufacturer
Load
Load
G3NA-205B
G3NA-210B
G3NA-220B
G3NA-240B
G3NA-275B-UTU(-2)
G3NA-290B-UTU(-2)
Applicable SSR
Load power
supply
G3NA
15