G3NH-2150B DC5-24 Omron, G3NH-2150B DC5-24 Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
G3NH-2150B DC5-24
Manufacturer Part Number
G3NH-2150B DC5-24
Description
RELAY SSR 150A 5VDC
Manufacturer
Omron
Series
G3NHr
Datasheet
1.G3NH-4150B_DC5-24.pdf
(6 pages)
Specifications of G3NH-2150B DC5-24
Circuit
SPST-NO (1 Form A)
Output Type
AC, Zero Cross
Load Current
150A
Voltage - Input
4 ~ 30VDC
Voltage - Load
75 ~ 264 V
Mounting Type
Chassis Mount
Termination Style
Screw Terminal
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
On-state Resistance
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
G3NH-2150B-DC5-24
G3NH2150BDC524
G3NH2150BDC524NC
G3NH2150BDC524
G3NH2150BDC524NC
Replacement
Be sure to turn off the power before replacement.
1. First, remove the four screws (shown below as “A”) and the
2. Remove the four screws (shown in the following as “B”) and the
3. Remove the three screws (shown in the following as “C”) from
4. When the Base Assembly is detached, you will see the leads
5. Remove the two screws (shown in the following as “D”) and take
transparent protective cover from the relay housing and then
disconnect the wiring.
nameplate from the relay housing.
inside the housing and pull the Base Assembly up to detach. (The
Base Assembly cannot be removed thoroughly because of the
leads connected to the base.)
connected to the built-in thyristor module. Pull the connector to
disconnect the leads. At this point, if any defect exists in any of
the electronic components on the PWB, the SSR may fail again
even after the replacement of the built-in thyristor module. In such
a case, consult OMRON about appropriate remedial action.
out the built-in thyristor module.
Protection cover
securing groove
A
A
B
B
PWB
Connector
Base
Name plate
Connecting to thyristor module
Protection cover
C
B
B
A
A
Assembly of the thyristor module must be performed in the exact
reverse order of the previous disassembly steps 1 to 5.
6. Before mounting the new thyristor module for replacement, wipe
7. Connect the thyristor module to the PWB with the socket. (The
8. Secure the Base Assembly with the three screws “C”. Because a
9. Check the assembled parts again for any lead caught between
10.Complete the wiring and secure the protective cover with the four
11.Apply power to the relay and check the relay for proper operation.
off the silicone grease adhering to the heat sink, keep clean the
jointing surfaces of the heat sink and thyristor module, and apply
the new grease (supplied as an accessory) to the jointing
surfaces. Secure the thyristor module to the heat sink with the two
screws “D” and tighten each screw to a torque of 2.45 to
2.94 N·m.
socket may be inserted in either direction.) Assemble the Base
Assembly with the heat sink by aligning the PWB with the PWB
securing groove and the protective cover with the protective cover
securing groove, respectively, while exercising caution not to get
any of the leads caught between the Base Assembly and the heat
sink.
large current flows into these screw parts, make sure that any of
the screws is not clogged with foreign matter and tighten each
screw to a torque of 4.41 to 4.90 N·m.
the Base Assembly and heat sink and for proper fitting of the
PWB and protective cover into their respective securing grooves.
Then, replace the nameplate and secure it with the four screws
“B”.
screws “A”.
PWB securing groove
Heat sink
D
D
G3NH
4