CRA06P08382R0JTA Vishay, CRA06P08382R0JTA Datasheet - Page 3
![RES ARRAY 82 OHM 8TRM 4RES SMD](/photos/9/65/96541/vishay_-_cra04p_sml.jpg)
CRA06P08382R0JTA
Manufacturer Part Number
CRA06P08382R0JTA
Description
RES ARRAY 82 OHM 8TRM 4RES SMD
Manufacturer
Vishay
Series
CRA06r
Datasheet
1.CRA06P083220RJTA.pdf
(4 pages)
Specifications of CRA06P08382R0JTA
Resistance (ohms)
82
Number Of Resistors
4
Circuit Type
Isolated
Temperature Coefficient
±200ppm/°C
Tolerance
±5%
Power Per Element
62.5mW
Number Of Pins
8
Package / Case
1206 (3216 Metric), Concave
Size / Dimension
0.126" L x 0.063" W (3.20mm x 1.60mm)
Height
0.024" (0.60mm)
Mounting Type
Surface Mount
Operating Temperature
-55°C ~ 155°C
Lead Free Status / RoHS Status
Lead free by exemption / RoHS Compliant
CRA06P
Vishay
Notes
(1)
(2)
www.vishay.com
258
TEST PROCEDURES AND REQUIREMENTS
TEST
(clause)
Resistance (4.5)
Temperature coefficient (4.8.4.2)
Overload (4.13)
Solderability (4.17.5)
Resistance to soldering heat (4.18.2)
Rapid change of temperature (4.19)
Damp heat, steady state (4.24)
Climatic sequence (4.23)
Endurance at 70 °C (4.25.1)
Extended endurance (4.25.1.8)
Endurance at upper category
temperature (4.25.3)
APPLICABLE SPECIFICATIONS
• EN 60115-1
• EN 140400
• EN 140401-802
• IEC 60068-2-X
• EIA 481
Figures are given for a single element
Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years
(2)
Generic Specification
Sectional Specification
Detail Specification
Variety of environmental test procedures
Packaging of SMD components
For technical questions, contact: filmresistors.thickfilmchip@vishay.com
CONDITIONS OF TEST
Stability for product types:
16 h at UCT = 125 °C; 1 cycle at 55 °C;
U = U
U = U
30 min at UCT = 125 °C; 5 cycles
Solder bath method; 235 °C; 2 s
Aging 4 h at 155 °C, dryheat
Duration extended to 8000 h
1 h/1 kPa at 15 °C to 35 °C;
30 min at LCT = - 55 °C;
(260 ± 5) °C; (10 ± 1) s
max.
max.
UCT = 125 °C; 1000 h
U = 2.5 × (P
1.5 h ON; 0.5 h OFF;
(40 ± 2) °C; 56 days;
2 h at LCT = - 55 °C;
Solder bath method;
Thick Film Resistor Array
Visual examination
20/- 55/20 °C and
≤ 2 x U
5 cycles at 55 °C
; whichever is less severe
; whichever is less severe
U = (P
U = (P
(93 ± 3) % RH
70 °C; 1000 h
20/125/20 °C
max.
70
70
-
EN 60115-1
x R)
x R)
70
; 0.5 s
x R)
1/2
1/2
1/2
CRA06P
CLASS 1 OR BETTER
± (0.25 % R + 0.05 Ω)
± (0.25 % R + 0.05 Ω)
± (0.25 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (2 % R + 0.1 Ω)
10 Ω to 1 MΩ
± 100 ppm/K
STABILITY
PERMISSIBLE CHANGE (ΔR/R)
± 1 %
Good tinning (≥ 95 % covered)
REQUIREMENTS
no visible damage
Document Number: 31047
CLASS 2 OR BETTER
± (0.5 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
± (2 % R + 0.1 Ω)
± (2 % R + 0.1 Ω)
± (2 % R + 0.1 Ω)
± (4 % R + 0.1 Ω)
± (2 % R + 0.1 Ω)
10 Ω to 1 MΩ
± 2 %; ± 5 %
± 200 ppm/K
Revision: 13-Oct-08
STABILITY
(1)