63819-1200 Molex Inc, 63819-1200 Datasheet
63819-1200
Specifications of 63819-1200
063819-1200-E
0638191200
0638191200-E
63819-1200-E
638191200
638191200-E
WM9024
63819-1200 Summary of contents
Page 1
... Terminal #1973 maximum diameter - 2.85mm (.112 inch AWG Profile minimum diameter (all terminals) - 1.70mm (.067 inch) Doc No: ATS-638191200 Release Date: 01-10-08 Revision: A Revision Date: 01-10-08 HAND CRIMP TOOL Specification Sheet Order No. 63819-1200 Æ Wire Size Insulation Diameter + Reel AWG mm² mm 18-22 0.82-0.32 1 ...
Page 2
... After crimping, the conductor profiles should measure the following. Terminal Series No AWG mm 1380 1381 1457-1 1881-2 1973 2273 4272 6271 Doc No: ATS-638191200 Release Date: 01-10-08 Revision: A Revision Date: 01-10-08 CONDUCTOR BELL MOUTH CRIMP INSULATION CRIMP CRIMP HEIGHT Wire Size Conductor Crimp 2 Height (Ref ...
Page 3
... See Figure 1. Crimping Terminals 1. Select the desired terminal listed from the preceding charts, and install the proper locator (See chart above and see Locator Installation on page 5). Doc No: ATS-638191200 Release Date: 01-10-08 Revision: A Revision Date: 01-10-08 PULL Force ...
Page 4
... Release the handles to open the jaws. TERMINAL PRE-STRIPPED WIRE Note: The tamper proof ratchet action will not release the tool until it has been fully closed. Doc No: ATS-638191200 Release Date: 01-10-08 Revision: A Revision Date: 01-10-08 LOCATOR PUSHED THRU ...
Page 5
... HANDTOOL TOP HOOKS Figure 7A LOWER TABS 3. Lift and pull away from the hand tool. The top locator hooks should slip out of the top slots easily. See Figure 7A. Doc No: ATS-638191200 Release Date: 01-10-08 Revision: A Revision Date: 01-10-08 MAKE SURE CENTER OF LOCATOR IS IN THE ...
Page 6
... When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the tool in a clean, dry area. Doc No: ATS-638191200 Release Date: 01-10-08 Revision: A Revision Date: 01-10-08 ...
Page 7
... This tool is designed for hand use only. Any clamping, fixturing, or use of handle extensions voids this warranty. CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling. Doc No: ATS-638191200 Release Date: 01-10-08 Revision: A ...
Page 8
... If the tool does not meet minimum pull force values, handle preload should be increased and the pull test rerun, (See How to Adjust Preload). % When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and replaced. Doc No: ATS-638191200 Release Date: 01-10-08 Revision: A Revision Date: 01-10-08 NOT ...
Page 9
... Lisle, Illinois 60532 U.S.A. Yamato, Kanagawa, Japan 1-800-78MOLEX 81-462-65-2324 amerinfo@molex.com feninfo@molex.com Doc No: ATS-638191200 Release Date: 01-10-08 Revision: A Revision Date: 01-10-08 Order Number Description 63819-1200 Hand Crimp Tool 63819-1175 Locator Assembly (Red) 63819-1176 Locator Assembly (Yellow) 63810-0104 Spring, Return 63810-0105 Spring, Ratchet 2 Figure 13 ...