64001-1500 Molex Inc, 64001-1500 Datasheet - Page 3

• Manufacturer Part Number: 64001-1500
• Description: TOOL CRIMP TERM 10-12, 14-16AWG
• Manufacturer: Molex Inc
• Series: Avikrimp®, Insulkrimp®r
• Type: Hand Crimp Toolr

Specifications of 64001-1500

• Tool Type: Hand Crimper
• Features: Side Entry, Ratchet
• Product: Crimping, Stripping & Cutting Tools & Drills
• Description/function: Full cycle ratcheting
• Wire Gauge Min (awg): 10-12
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• For Use With/related Products: Splices and Terminals, 10-16 AWG
• For Use With: WM19147 - CONN RING TERM #8 10-12AWGWM19144 - CONN RING TERM #8 10-12AWGWM18741 - CONN SNAP SPADE #8 10-12AWGWM18392 - CONN BUTTSPLICE 10-12TO14-16AWGWM18385 - CONN BUTT SPLICE 10-12AWGWM18382 - CONN WIRE PIN TERM 10-12AWGWM18379 - CONN WIRE PIN TERM 10-12AWGWM18373 - CONN TONGUE SPADE #1/4 10-12AWGWM18372 - CONN TONGUE SPADE #10 10-12AWGWM18371 - CONN TONGUE SPADE #8 10-12AWGWM18370 - CONN TONGUE SPADE #6 10-12AWGWM18362 - CONN TONGUE SPADE #1/4 10-12AWGWM18361 - CONN TONGUE SPADE #10 10-12AWGWM18360 - CONN TONGUE SPADE #8 10-12AWGWM18359 - CONN TONGUE SPADE #6 10-12AWGWM18351 - CONN FLANGED SPADE #10 10-12AWGWM18350 - CONN FLANGED SPADE #8 10-12AWGWM18335 - CONN SNAP SPADE #10 10-12AWGWM18334 - CONN SNAP SPADE #8 10-12AWGWM18333 - CONN SNAP SPADE #6 10-12AWGWM18323 - CONN SNAP SPADE #10 10-12AWGWM18321 - CONN SNAP SPADE #6 10-12AWGWM18314 - CONN RING TERM 1/2 10-12AWGWM18313 - CONN RING TERM 3/8 10-12AWGWM18312 - CONN RING TERM 5/16 10-12AWGWM18310 - CONN RING TERM #10 10-12AWGWM18309 - CONN RING TERM #8 10-12AWGWM18308 - CONN RING TERM #6 10-12AWGWM18291 - CONN RING TERM 3/8 10-12AWGWM18290 - CONN RING TERM 5/16 10-12AWGWM18289 - CONN RING TERM 1/4 10-12AWGWM18288 - CONN RING TERM #10 10-12AWGWM18287 - CONN RING TERM #8 10-12AWGWM18286 - CONN RING TERM #6 10-12AWG
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 064001-1500; 064001-1500-E; 0640011500; 0640011500-E; 64001-1500-E; 640011500; 640011500-E; WM17468

TERMINAL
Maintenance
It is recommended that each operator of the tool
be made aware of, and responsible for, the
following maintenance steps:
Doc No. 64001-1500 Release Date: 01-15-03
Revision: C
RHT 2200 Hand Crimp Tool
LOCATOR
4. Lift the locator blade or wire stop and remove the crimped
5. If the insulation part of the crimp needs to be adjusted, first
6. When crimping butt splices, or 3-way and 4-way terminals the
1. Remove dust, moisture, and other
2. Do not use any abrasive materials that
terminal. Inspect for proper crimp location, and check for
insulation closure. Locator is adjustable up and down to keep
terminals straight after crimping.
loosen the M4 screw on the bottom tool jaw, then insert a 3/32
hex wrench (supplied) into the bottom of the lower die (See
Figure 5). A clockwise (CW) rotation decreases insulation crimp
while a counter-clockwise (CCW) rotation increases insulation
crimp. After adjusting retighten the M4 screw.
locator must be removed. Splices must be aligned with the
tooling visually in the insulation crimp (See Figure 4). The splice
should be approximately centered inside the tooling nests (See
Figure 4). Cycle the tool.
Note: Whenever crimping without the locator, make sure the seam of the terminal is
oriented up or down in the tool if using unbrazed product, as this will provide higher pull
force values.
contaminants with a clean brush, or soft,
lint free cloth.
could damage the tool.
CONDUCTO
CONDUCTO
R
R
Revision Date: 01-10-06
Figure 3
INSULATION
PUNCH
INSULATIO
N
TERMINA
WIRE
L
3/32” HEX
WRENCH
UNCONTROLLED COPY
LOOSEN
SPLICE
BUTT
M4
CONDUCTOR
CONDUCTO
PUNCH
R
Figure 5
TERMINAL
Figure 4
LUBRICATION POINTS
(BOTH SIDES) LIGHT
(EVERY 3 MONTHS
Figure 2
OR 5,000 CRIMPS)
OIL
INSULATION
WIRE
INSULATIO
Page 3 of 7
PUNCH
N
WIRE