64001-4500 Molex Inc, 64001-4500 Datasheet

TOOL CRIMP SEALED 14-22AWG .250

64001-4500

Manufacturer Part Number
64001-4500
Description
TOOL CRIMP SEALED 14-22AWG .250
Manufacturer
Molex Inc
Series
Perma-Seal™r
Datasheets
1.64016-0201.pdf (1 pages)
2.19284-0034.pdf (27 pages)
3.64001-4500.pdf (6 pages)

Specifications of 64001-4500

Tool Type
Hand Crimper
Features
Side Entry, Ratchet
Lead Free Status / RoHS Status
Not applicable / Not applicable
For Use With/related Products
Quick Connects Terminals and Splices, 10-22 AWG
For Use With
WM2964 - CONN SPLICE BUTT 14/16-18/22AWGWM18950 - CONN SPLICE BUTT 10/12-14/16AWGWM18431 - CONN .250"FEMALE SEALED 14-16AWGWM18430 - CONN .250"MALE SEALED 14-16AWGWM18429 - CONN .250"FEMALE SEALED 18-22AWGWM18428 - CONN .250"MALE SEALED 18-22AWG
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
064001-4500
064001-4500-E
0640014500
0640014500-E
64001-4500-E
640014500
640014500-E
WM9976
RHT-5771 Hand Crimp Tool
Doc No. 64001-4500
Revision: B
FEATURES
Œ
Œ
Œ
SCOPE
Perma-Seal Step Down Butt Splices for 14-16 to 18-22 AWG and 10-12 to 14-16 AWG. FIQD Couplers Male and Female for
14-22 AWG.
Testing
The following is a partial list of the product part numbers and their specifications that this tool is designed to run. We will be adding to
this list and an up to date copy is available on www.molex.com.
Mechanical
The tensile test, or pull test, is a means of evaluating the mechanical properties of the crimped connections. The following charts
show the UL specifications for various wire sizes. The tensile strength is shown in pounds, and it indicates the minimum acceptable
force to break or separate the terminal from the conductor.
A full cycle ratcheting hand tool ensures complete crimps
An economical tool for portable crimping and field repair
3-nested tool eliminates the need for additional tools
Release Date: 10-24-03
Revision Date: 07-05-06
Operating Instruction Sheet and Specifications
Wire Size (AWG)
*UL - 486 A - Terminals (copper conductors only).
22
20
18
16
14
12
10
Part No. 64001-4500
(Replaces 19285-0051)
Eng. No. RHT 5771
**UL - 486 C - Butt Splices
***UL – 310 – Couplers
Hand Crimp Tool
UL – 486 A*
Min. Pull
13
20
30
50
70
80
8
UNCONTROLLED COPY
UL – 486 C**
Min. Pull
10
10
15
25
35
40
8
UL*310***
Min. Pull
13
20
30
50
70
80
8
Page 1 of 6

64001-4500 Summary of contents

Page 1

... The following is a partial list of the product part numbers and their specifications that this tool is designed to run. We will be adding to this list and date copy is available on www.molex.com. Doc No. 64001-4500 Release Date: 10-24-03 Revision: B Revision Date: 07-05-06 Hand Crimp Tool Part No. 64001-4500 Eng. No. RHT 5771 (Replaces 19285-0051) UL – 486 A* UL – 486 C** Min. Pull Min. Pull ...

Page 2

... Insert the properly stripped wire into the terminal barrel (See Figure 2 and 3). TERMINAL Figure 2 6. Complete the crimp by closing the hand tool handles until they release. Note: The tamper proof ratchet action will not release the tool until it has been fully closed. Doc No. 64001-4500 Release Date: 10-24-03 Revision: B Revision Date: 07-05-06 mm ...

Page 3

... Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil excessively. The 64001-4500 (RHT-5771) was engineered for durability, but like any fine piece of equipment, it needs cleaning and lubrication for a maximum service life of trouble-free crimping ...

Page 4

... Caution: Repetitive use of this tool should be avoided. Hand held crimping tools are intended for low volume, prototyping, or repair requirements only. CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling. Doc No. 64001-4500 Release Date: 11-06-03 Revision: B ...

Page 5

... RHT-5771 Hand Crimp Tool PARTS LIST Item LOCKNUT W/ HEX NYLON INSERT M4 FLAT WASHER Doc No. 64001-4500 Release Date: 11-06-03 Revision: B Revision Date: 07-05-06 Order No Description 64001-4500 Hand Crimp Tool 64000-0076 Repair Kit (Springs, Pins and E-Rings) 63810-0000 Handle 64001-4575 Locator Assembly 64001-4570 ...

Page 6

... Date of Calibration ___________________ Calibration should be done every 5,000 cycles or 3 months. Tools should be lubricated during this operation. Americas Headquarters Far East North Headquarters Doc No. 64001-4500 Release Date: 11-06-03 Revision: B Revision Date: 07-05-06 Certificate of Calibration Handle Load Range at 1 inch from the Tips =_______________ Far East South Headquarters Visit our Web site at http://www ...