63819-0800 Molex Inc, 63819-0800 Datasheet
63819-0800
Specifications of 63819-0800
063819-0800-P
0638190800
0638190800-P
63819-0800
63819-0800-P
638190800
638190800-P
Q3830189
WM9021
63819-0800 Summary of contents
Page 1
... Customer to cut off terminal from reel: 0.13mm (.005”) maximum Cut-off Tab. Doc No: ATS-638190800 Release Date: 10-25-07 Revision: B Revision Date: 03-09-08 HAND CRIMP TOOL Specification Sheet Order No. 63819-0800 Æ Wire Size Reel AWG mm² 24-30 0.20-0.05 1.02-1.78 .040-.070 3.17-3.96 .125-.156 24-30 0 ...
Page 2
... Doc No: ATS-638190800 Release Date: 10-25-07 Revision: B Revision Date: 03-09-08 CONDUCTOR BELL MOUTH CRIMP INSULATION CRIMP CRIMP HEIGHT Conductor Crimp Height (Ref.) Width (Ref.) Height (Ref.) Width (Ref In. mm In. 0.20 0.69-0.79 .027-.031 1.41 .055 0.12 0.65-0.75 .025-.029 1.37 ...
Page 3
... See Figure 2. 3. While holding the locator button in, load the terminal into the proper nest opening in the locator based on the wire gauge or terminal type markings on the hand tooling. See Figure 3. Doc No: ATS-638190800 Release Date: 10-25-07 Revision: B ...
Page 4
... Release the handles to open the jaws. TERMINAL PRE-STRIPPED WIRE Note: The tamper proof ratchet action will not release the tool until it has been fully closed. Doc No: ATS-638190800 Release Date: 10-25-07 Revision: B Revision Date: 03-09-08 LOCATOR LOCATOR ...
Page 5
... Rotate the locator down and press the lower tabs into the two bottom slots of the hand tool. To secure the locator into place, the lower tabs must snap into place on the hand tool frame. Doc No: ATS-638190800 Release Date: 10-25-07 Revision: B Revision Date: 03-09-08 ...
Page 6
... Miscrimps or Jams Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or closed. pressing up on the ratchet release lever in the movable handle. See Figure 9. Doc No: ATS-638190800 Release Date: 10-25-07 Revision: B Revision Date: 03-09-08 FRONT ...
Page 7
... Repetitive use of this tool should be avoided. 2. Insulated rubber handles are not protection against electrical shock. 3. Wear eye protection at all times. 4. Use only the Molex terminals specified for crimping with this tool. Doc No: ATS-638190800 Release Date: 10-25-07 Revision: B Revision Date: 03-09-08 ...
Page 8
... If the tool does not meet minimum pull force values, handle preload should be increased and the pull test rerun, (See How to Adjust Preload). % When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and replaced. Doc No: ATS-638190800 Release Date: 10-25-07 Revision: B Revision Date: 03-09-08 UNCONTROLLED COPY ...
Page 9
... Lisle, Illinois 60532 U.S.A. Yamato, Kanagawa, Japan 1-800-78MOLEX 81-462-65-2324 amerinfo@molex.com feninfo@molex.com Doc No: ATS-638190800 Release Date: 10-25-07 Revision: B Revision Date: 03-09-08 Order Number Description 63819-0800 Hand Crimp Tool 63819-0875 Locator Assembly (Red) 63819-0876 Locator Assembly (Yellow) 63810-0104 Spring, Return 63810-0105 Spring, Ratchet 2 Figure 13 ...