63811-8600 Molex Inc, 63811-8600 Datasheet

TOOL HAND CRIMP 20-22AWG

63811-8600

Manufacturer Part Number
63811-8600
Description
TOOL HAND CRIMP 20-22AWG
Manufacturer
Molex Inc
Series
PremiumGrade™r
Type
Crimp Toolr
Datasheets
1.64016-0201.pdf (1 pages)
2.63811-7500.pdf (24 pages)
3.63811-8600.pdf (7 pages)

Specifications of 63811-8600

Tool Type
Hand Crimper
Features
Side Entry, Ratchet
Product
Crimping, Stripping & Cutting Tools & Drills
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
Rectangular Contacts, 20-22 AWG
For Use With
WM17529 - CONN PIN 20-22AWG TIN CRIMPWM17525 - CONN SOCKET 20-22AWG TIN
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
063811-8600
063811-8600-P
0638118600
0638118600-P
63811-8600-P
638118600
638118600-P
WM17530
Hand Crimp Tool for 2.50mm (.098”) Pitch Wire-to-Wire Splash Proof Crimp Terminal
Doc No. ATS-638118600
Revision: A
FEATURES
Œ
Œ
Œ
Œ
Œ
Œ
SCOPE
Products: 2.50mm (.098”) Pitch Wire-to-Wire Splash Proof Crimp Terminal
0.30mm)
DEFINITION OF TERMS
The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope.
A full cycle ratcheting hand tool ensures complete crimps
Ergonomic soft grip handles for comfortable crimping
A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position
Right and Left handed applications
This tool is IPC/WHMA A-620 Class 2 compliant
This tool is RoHS compliant, however RoHS compliant is not required
BRUSH
Series No. Loose Piece
Terminal
50147
50148
LENGTH
STRIP
50147-8100 50147-8000 20-22 0.50-0.30 1.40-1.90 .055-.075 2.00-2.50 .079-.098
50148-8100 50148-8000 20-22 0.50-0.30 1.40-1.90 .055-075 2.00-2.50 .079-.098
Release Date: 07-16-07
Revision Date: 07-16-07
Æ
Terminal Order No.
Follow the Cut-Off Tab specifications on Applicator specification sheets.
BELL MOUTH
Æ
Reel
INSULATION
Order No. 63811-8600
HAND CRIMP TOOL
Specification Sheet
CRIMP
AWG
Wire Size
CONDUCTOR
mm²
UNCONTROLLED COPY
CRIMP
Insulation Diameter
CRIMP HEIGHT
mm
,
20-22 AWG (AVSS and CAVS 0.50-
In.
BEND UP
DOWN
BEND
mm
Strip Length
TWISTING
ROLLING
In.
TYPE 4D
Page 1 of 7

63811-8600 Summary of contents

Page 1

... LENGTH The above terminal drawing is a generic terminal representation not an image of a terminal listed in the scope. Doc No. ATS-638118600 Release Date: 07-16-07 Revision: A Revision Date: 07-16-07 HAND CRIMP TOOL Specification Sheet Order No. 63811-8600 Æ Wire Size Insulation Diameter Reel AWG mm² mm CONDUCTOR ...

Page 2

... While holding the locator button in, load the terminal into the proper nest opening in the locator based on the wire gauge or terminal type markings on the hand tooling. See Figure 3. LOCATOR PUSHED THRU TOOLING TERMINAL Doc No. ATS-638118600 Release Date: 07-16-07 Revision: A Revision Date: 07-16-07 Conductor Crimp Insulation Crimp Width (Ref ...

Page 3

... An occasional, destructive, pull force test should be performed to check hand tool crimp. Pull Force value Must exceed the Minimum pull force specifications listed. Doc No. ATS-638118600 Release Date: 07-16-07 Revision: A Revision Date: 07-16-07 ...

Page 4

... Flip the upper tooling to the opposite side and replace the M3 BHCS. Make sure the small markings on the front and back of the hand tool frame match up and are on the outside of the hand tool frame. See Figure 11 and 12. Doc No. ATS-638118600 Release Date: 07-16-07 Revision: A Revision Date: 07-16-07 LOCATOR ...

Page 5

... Rotate the setting wheel counter-clockwise (CCW) to increase handle force. The numbers will display higher. To decrease handle force rotate the setting wheel clockwise (CW). 3. Release the link to lock the setting wheel in place. 4. Check the crimp specifications or conduct a pull test after tool handle preload force is adjusted. Doc No. ATS-638118600 Release Date: 07-16-07 Revision: A Revision Date: 07-16-07 ...

Page 6

... If the tool does not meet minimum pull force values, handle preload should be increased and the pull test rerun, (See How to Adjust Preload). % When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and replaced. Doc No. ATS-638118600 Release Date: 07-16-07 Revision: A Revision Date: 07-16-07 SQUEEZE ...

Page 7

... Lisle, Illinois 60532 U.S.A. Yamato, Kanagawa, Japan 1-800-78MOLEX 81-462-65-2324 amerinfo@molex.com feninfo@molex.com Doc No. ATS-638118600 Release Date: 07-16-07 Revision: A Revision Date: 07-16-07 Order Number Description 63811-8600 Hand Crimp Tool 63811-8675 Locator Assembly 63810-0104 Spring, Return 63810-0105 Spring, Ratchet 2 Figure 13 Far East South Headquarters European Headquarters ...