64001-4600 Molex Inc, 64001-4600 Datasheet

TOOL HAND CRIMP 10-12AWG .25O

64001-4600

Manufacturer Part Number
64001-4600
Description
TOOL HAND CRIMP 10-12AWG .25O
Manufacturer
Molex Inc
Series
Avikrimp®r
Type
Crimp Tool Assemblyr
Datasheets
1.64016-0201.pdf (1 pages)
2.19284-0034.pdf (27 pages)
3.64001-4600.pdf (6 pages)
4.64001-4600.pdf (1 pages)

Specifications of 64001-4600

Tool Type
Hand Crimper
Features
Side Entry, Ratchet
Product
Crimping, Stripping & Cutting Tools & Drills
Description/function
Hand crimp tool assembly
Lead Free Status / RoHS Status
Not applicable / Not applicable
For Use With/related Products
Quick Connects Terminals, 10-12 AWG
For Use With
WM18229 - CONN .250" MALE INSUL 10-12AWG
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
064001-4600
064001-4600-E
0640014600
0640014600-E
64001-4600-E
640014600
640014600-E
WM17466
RHT-5764 Hand Crimp Tool
Doc No. 64001-4600 Release Date: 11-10-03
Revision: A
FEATURES
Œ
Œ
Œ
Œ
Œ
SCOPE
The following is a partial list of the product part numbers and their specifications that this tool is designed to run.
We will be adding to this list and an up to date copy is available on www.molex.com.
AviKrimp Male Quick Disconnect 10-12 AWG
Testing
A full cycle ratcheting hand tool ensures complete crimps
Long handles for comfortable crimping with reduced crimping force
A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position
Insulation crimp adjustment allows a precise insulation crimp. To meet or exceed the requirements of UL, CSA
and Military Cass II
Single color-coded crimp pocket eliminates the possibility of using the wrong pocket
Mechanical
The tensile test or pull test, is a means of evaluating the mechanical properties of the crimped connections.
The following charts show the UL specifications for various wire sizes. The tensile strength is shown in
pounds and indicates the minimum acceptable force to break or separate the terminal from the conductor.
Revision Date: 11-10-03
19001-0010
Terminal No.
Operating Instruction Sheet and Specifications
Wire Size: 10 – 12 AWG
Terminal Eng No. (REF)
*UL – 310 – Quick Disconnects
Part No. 64001-4600
Wire Size (AWG) *UL - 310
(Replaces 19285-0045)
C-5264
Eng. No. RHT 5764
Hand Crimp Tool
12
10
UNCONTROLLED COPY
Wire Strip Length
.340
In.
5.00 – 3.30 mm²
70
80
8.73
mm
Insul. Dia. Max.
.230
In.
5.84
mm
Page 1 of 6

64001-4600 Summary of contents

Page 1

... The following is a partial list of the product part numbers and their specifications that this tool is designed to run. We will be adding to this list and date copy is available on www.molex.com. Terminal No. 19001-0010 Doc No. 64001-4600 Release Date: 11-10-03 Revision: A Revision Date: 11-10-03 Hand Crimp Tool Part No. 64001-4600 Eng ...

Page 2

... M4 screw. TERMINAL Figure 2 Note: Whenever crimping without the locator, make sure the seam of the terminal is oriented up or down in the tool if using unbrazed product, as this will provide higher pull force values. Doc No. 64001-4600 Release Date: 11-10-03 Revision: A Revision Date: 11-10-03 LOCATOR CONDUCTOR ...

Page 3

... Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil excessively. The 64001-4600 (RHT-5764) was engineered for durability, but like any fine piece of equipment it needs cleaning and lubrication for a maximum service life of trouble-free crimping ...

Page 4

... Hand held crimping tools are intended for low volume, prototyping or repair requirements only. Caution: Repetitive use of this tool should be avoided. Doc No. 64001-4600 Release Date: 11-10-03 Revision: A Revision Date: 11-10-03 “X” Dimension Conductor Crimp mm² ...

Page 5

... The following purchased parts are available from an Industrial supply company such as MSC (1-800-645- 7270). M4 LOCKNUT W/ HEX NYLON INSERT M4 FLAT WASHER Doc No. 64001-4600 Release Date: 11-10-03 Revision: A Revision Date: 11-10-03 Order No Description 64001-4600 Hand Crimp Tool 64000-0076 Repair Kit (Springs, Pins and E-Rings) 63810-0000 ...

Page 6

... Range Conductor Nest # 3 = ____N/A____-- Actual = ______________ Technician ______________ Date of Calibration ______________ Calibration should be done every 5,000 cycles or 3 months. Tools should be lubricated during this operation. Doc No. 64001-4600 Release Date: 11-10-03 Revision: A Revision Date: 11-10-03 Certificate of Calibration Handle Load Range at 1 inch from the Tips =______________ Molex Application Tooling Group 1150 E ...