90758-2 Tyco Electronics, 90758-2 Datasheet

DIE SET FOR PRO-C III 26-22 AWG

90758-2

Manufacturer Part Number
90758-2
Description
DIE SET FOR PRO-C III 26-22 AWG
Manufacturer
Tyco Electronics
Series
Pro-Crimper™ III, Mini Universal MATE-N-LOK®r
Type
Die Crimp Toolr
Datasheets
1.90758-1.pdf (6 pages)
2.58637-2.pdf (8 pages)

Specifications of 90758-2

Connector Type
Crimp Terminals
Crimp Handle
A9966-ND
Crimp Or Cable Size
22-26 AWG
Crimp Application
D-sub Pins And Sockets
Wire Area Size Max
0.4mm2
Wire Area Size Min
0.15mm2
Wire Size Awg Max
22AWG
Wire Size Awg Min
26AWG
Product
Crimping, Stripping & Cutting Tools & Drills
Description/function
Tool for crimping terminals
Lead Free Status / RoHS Status
Not applicable / Not applicable
For Use With
A25584 - PROCRIMPER III W/DIE 22-26 AWG
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
A30039
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended- - use, production operations is available.
{ Supplied with die assembly. Also available separately.
} Contact the TOOLING ASSISTANCE CENTER or PRODUCT INFORMATION (see below) for specific contact part numbers.
1. INTRODUCTION
PRO--CRIMPER III Hand Crimping Tool
Assembly 90759--1 consists of Die Assembly
90759--2 and PRO--CRIMPER III Hand Crimping Tool
Frame 354940--1. The die assembly consists of
crimping dies and a locator assembly.
Read these instructions thoroughly before crimping
any contacts.
E2009 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
The PRO- - CRIMPER III Hand Crimping Tool is a “Commercial” grade tool and
is designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate 114 series specification, but may not comply with other feature
parameters of the specification. Tyco Electronics offers a variety of tools to
satisfy your performance requirements. For additional information, contact the
Tooling Assistance Center at 1- - 800- - 722- - 1111.
TE Die Assembly
TE Die Assembly
NOTE
i
90759--2
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures
and illustrations are for identification only and are
not drawn to scale.
Die Assembly
Locator Assembly
(Supplied with
Die Assembly)
Assembly{
TE Locator
TE Locator
58516--1
Front of Tool
(Locator Side)
Moving Jaw
Ratchet
Adjustment
Wheel
TOOLING ASSISTANCE CENTER 1- - 800- - 722- - 1111
PRODUCT INFORMATION 1- - 800- - 522- - 6752
PRO- CRIMPER* III Hand
Crimping Tool Assembly 90758- 1
with Die Assembly 90758- 2
MATE--N--LOK*
Mini Universal
Connectors
Contact
Contact
Family}
Figure 1
Reasons for reissue are provided in Section 11,
REVISION SUMMARY.
2. DESCRIPTION
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
adjustable ratchet that ensures full contact crimping.
The tool frame holds a die assembly with two
crimping sections.
The die assembly features a wire anvil, an insulation
anvil, a wire crimper, and an insulation crimper.
Size (AWG)
26--22
Stationary Jaw
Moving Handle
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
(Figures 1 and 2)
Pivot Pin
[.047 to .069]
1.19 to 1.75
Insul Dia
Wire
Back of Tool
(Wire Side)
PRO- - CRIMPER III Hand
Crimping Tool Frame
354940- - 1 (408- - 9930)
Stationary
Handle
Instruction Sheet
408- - 9938
08 OCT 09 Rev B
Strip Length
[.126 to .146]
3.20 to 3.71
1 of 6
LOC B

90758-2 Summary of contents

Page 1

... All International Rights Reserved TE logo and Tyco Electronics are trademarks. *Trademark. Other products, logos, and company names used are the property of their respective owners. PRO- CRIMPER* III Hand Crimping Tool Assembly 90758- 1 with Die Assembly 90758- 2 Stationary Jaw Moving Jaw Ratchet Adjustment ...

Page 2

... CONTACT SUPPORT ADJUSTMENT NOTE i 1. Make a sample crimp and determine if the contact is straight, bending upward, or bending downward. Tyco Electronics Corporation Tool Frame Die Retaining Pins Die Retaining Screws ) (Figure 3 The contact support is preset prior to shipment, but minor adjustment may be necessary ...

Page 3

... Make sure that both sides of the insulation barrel CAUTION are started evenly into the crimping section NOT attempt to crimp an improperly positioned contact. Back of Tool (Wire Side) Contact (Typ) Locator in Wire Wire Stop Slot Figure 3 Tyco Electronics Corporation Strip Length Wire Inserted to Stop ...

Page 4

... Do not use objects that could .69 [.027] damage the tool. When not in use, keep handles closed to prevent objects from becoming lodged in .79 [.031] the crimping dies, and store in a clean, dry area. Tyco Electronics Corporation (Figure 5) Screwdriver Lockscrew (Typ) Figure 5 ...

Page 5

... Revisions to this instruction sheet include: Changed PRO--CRIMPER II Hand Tool to S PRO--CRIMPER III Hand Tool; Revised crimp--height comparator information; S Applied TE logo; S Updated format to current corporate S requirements; and Added back page indicating tooling compatible S with dies 90758--2. Tyco Electronics Corporation ...

Page 6

... SDE Bench Terminator 1490076- 2 (Customer Manual 409- 10052) Battery Tool (Shouldered Die) 1725837 (Customer Manual 409- 10053 Tooling Used With Dies 90758- 2 SDE PEW- 12 Hand Tool 9- 1478240- 0 626 Adapter 679304- 1 (Instruction Sheet 408- 4070) Battery Tool (Pin Die) 1213890 Tyco Electronics Corporation ...