58495-2 Tyco Electronics, 58495-2 Datasheet

TOOL DIE SET CPC CONN TYPE III

58495-2

Manufacturer Part Number
58495-2
Description
TOOL DIE SET CPC CONN TYPE III
Manufacturer
Tyco Electronics
Series
Pro-Crimper™ IIIr
Type
Hand Toolr
Datasheets
1.1673606-1.pdf (8 pages)
2.58495-1.pdf (6 pages)
3.58448-2.pdf (5 pages)

Specifications of 58495-2

Connector Type
Crimp Terminals
Crimp Handle
A9996-ND
Crimp Or Cable Size
16-28 AWG
Product
Crimping, Stripping & Cutting Tools & Drills
Lead Free Status / RoHS Status
Not applicable / Not applicable
Lead Free Status / RoHS Status
na, Not applicable / Not applicable
Other names
A9919
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended- - use, production operations is available.
1. INTRODUCTION
PRO--CRIMPER III Hand Crimping Tool Assembly
58495--1 consists of Die Assembly 58495--2 and
PRO--CRIMPER III Hand Crimping Tool Frame
354940--1. The die assembly consists of crimping
dies and a locator assembly.
Read these instructions thoroughly before crimping
any contacts.
E2009 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
The PRO- - CRIMPER III Hand Crimping Tool is a “Commercial” grade tool
and is designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate 114 series specification, but may not comply with other feature
parameters of the specification. Tyco Electronics offers a variety of tools to
satisfy your performance requirements. For additional information, contact
the Technical Assistance Center at 1- - 800- - 722- - 1111.
{ Supplied with die assembly. Also available separately.
Assembly
58495--2
TE Die
TE Die
Die Assembly
Locator
Assembly
(Supplied with
Die Assembly)
Front of Tool
(Locator Side)
Assembly
Locator
Locator
58515--1
Moving Jaw
{
Ratchet
Adjustment
Wheel
TOOLING ASSISTANCE CENTER 1- - 800- - 722- - 1111
PRODUCT INFORMATION 1- - 800- - 522- - 6752
PRO- CRIMPER* III Hand Crimping
Tool Assembly 58495- 1
With Die Assembly 58495- 2
Type III(+) and
Multimate
Multimate
Contact
Contact
C t t
Contacts
Family
Type VI
}
Figure 1
Reasons for reissue are provided in Section 11,
REVISION SUMMARY.
} Contact the Technical Assistance Center or Product Information (below) for
NOTE
i
(AWG)
specific product information.
28--24
24--20
18--16
Size
Stationary Jaw
Pivot Pin
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures
and illustrations are for identification only and are
not drawn to scale.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
Moving Handle
[.035 to .055]
[.040 to .080]
[.080 to .100]
1.02 to 2.03
2.03 to 2.54
Back of Tool
(Wire Side)
.89 to 1.40
PRO- - CRIMPER III Hand
Crimping Tool Frame
354940- - 1 (408- - 9930)
Insul
Wire
Dia
Stationary
Handle
Instruction Sheet
408- - 9819
22 JUL 09 Rev C
Strip Length
(mm [In.])
[.125]
3.17
1 of 6
LOC B

58495-2 Summary of contents

Page 1

... Supplied with die assembly. Also available separately. 1. INTRODUCTION PRO--CRIMPER III Hand Crimping Tool Assembly 58495--1 consists of Die Assembly 58495--2 and PRO--CRIMPER III Hand Crimping Tool Frame 354940--1. The die assembly consists of crimping dies and a locator assembly. Read these instructions thoroughly before crimping any contacts ...

Page 2

... Tyco Electronics Corporation PRO- - CRIMPER III Hand Tool Frame Die Retaining Pins ...

Page 3

... Refer to Figure 3. Butt the front end of the wire barrel against the movable locator. Back of Tool (Wire Side) Contact (Typ) Wire Locator in Wire Stop Slot Figure 3 Tyco Electronics Corporation Strip Length Wire Inserted to Stop ...

Page 4

... If the dimension is unacceptable, continue to adjust the ratchet, and again measure a sample crimp. Screwdriver Ratchet Adjustment Wheel (Figure 5) Lockscrew (Typ) Tyco Electronics Corporation “A” Crimp Height Dim. (A) and Tolerance 1.295.051 18--16 [.0510.0020] 1.003.051 24--20 [.0395 ...

Page 5

... If the dies are damaged or worn excessively, they must be replaced. Rev C Order the repair kit and replaceable parts through your Tyco Electronics representative, or call 1--800--526--5142, or send a facsimile of your purchase order to 1--717--986--7605, or write to: CUSTOMER SERVICE (38--35) TYCO ELECTRONICS ...

Page 6

... Dies 58495- 2 May Also Be Used with the Following Tools. PRO- CRIMPER III Hand Tool 354940- 1 (Instruction Sheet 408- 9930) SDE Bench Terminator 1490076- 2 (Customer Manual 409- 10052) Battery Tool (Shouldered Die) 1725837 (Customer Manual 409- 10053 SDE PEW- 12 Hand Tool 9- 1478240- 0 ...