47820 Tyco Electronics, 47820 Datasheet

DIE TERMINYL 69051 8AWG

47820

Manufacturer Part Number
47820
Description
DIE TERMINYL 69051 8AWG
Manufacturer
Tyco Electronics
Datasheet
1.47820.pdf (8 pages)

Specifications of 47820

Lead Free Status / RoHS Status
Not applicable / Not applicable
Crimping Dies 47820 through 47823 are used with
Crimping Head 69051 or Hand Tool 59974–1.
Crimping Dies 47824, 47825, 47915, and 47918 are
used with Crimping Head 69066. The dies crimp
pre–insulated AMPOWER* terminals onto wire sizes
4 through 1/0 AWG, TERMINYL* terminals and
splices onto wire sizes 8 through 4/0 AWG,
TERMINYL splices with step–down adapters onto
wire sizes 16–14 through 1/0 AWG, and
PLASTI–GRIP* terminals and splices onto wire sizes
8 through 4/0 AWG. Refer to Figure 1 to ensure
compatibility of crimping die, head or tool, and wire
size.
For detailed information about the head or tool, refer
to the instructions packaged with the head or tool.
Reasons for reissue of this instruction sheet are
provided in Section 8, REVISION SUMMARY.
Typical Crimping
Dies
E
i
Dimensions in this document are in millimeters
[with inches in brackets]. Figures and illustrations
are for reference only and are not drawn to scale.
Figure 1
Each crimping die consists of a stationary die (nest)
and a moving die (anvil). The stationary die features a
locator. Each die contains a color code dot that
matches the color code of the terminal and splice.
When mated, the dies form a crimping chamber.
1. Remove latch pin and open yoke on crimping
head. See Figure 2.
2. Loosen the setscrew in the yoke.
3. Insert the shank of the stationary die into the
yoke, and tighten the setscrew.
4. Extend the ram until the ram setscrew is visible.
5. Loosen the setscrew in the ram.
6. Insert the shank of the moving die into the ram,
and tighten the setscrew.
i
To avoid personal injury, ALWAYS release
hydraulic pressure to hose or control and
disconnect power unit from power supply before
installing or removing dies.
The stationary die has a large shank and the
moving die has a small shank, as shown in
Figure 2.
Figure 2

47820 Summary of contents

Page 1

... Typical Crimping Dies Figure 1 Crimping Dies 47820 through 47823 are used with Crimping Head 69051 or Hand Tool 59974–1. Crimping Dies 47824, 47825, 47915, and 47918 are used with Crimping Head 69066. The dies crimp pre–insulated AMPOWER* terminals onto wire sizes ...

Page 2

... Figure 3 Tyco Electronics Corporation Wire Stop Ç Ç Ç Ç É É É Ç Ç Ç Ç Window Indent 11.51-12.29 [.453-.484] 15.47-16.26 [.609-.640] 15.47-16.26 [.609-.640] 11.51-12.29 [.453-.484] 18 ...

Page 3

... Use the crimping die for the larger wire size to crimp both ends of the splice. For example, use Crimping Die 47820 (for wire size 8 AWG) to crimp both ends of the splice with step–down adapter for stepping down from wire size 8 to 16– ...

Page 4

... Splices with Step-Down Adapter Step-Down Adapter É É É É Ç Ç Ç Ç Ç Ç É É É É É É É É É É É É Ç Ç Ç Ç Ç Ç 16-14 47820 47820 Red Red 8 to 12- 47821 Blue 47822 ...

Page 5

... Crimping Dies 47820 through 47825, 47915, and 47918 If butt splice sticks in die after crimping, apply a NOTE rocking action to the butt splice to remove it from i the die. Wipe light oil on dies to reduce sticking, or use spray dry lubricant crimp the other half of butt splice, reposition ...

Page 6

... If damage is evident, the dies must be repaired before returning them to service (see Section 7, REPLACEMENT AND REPAIR Suggested Plug Gage Design GO Diameter Die Closure Configuration 5.105-5.113 47820 [.2010-.2013] 6.020-6.027 47821 [.2370-.2373] 6.833-6.840 47822 [.2690-.2693] 8.103-8.110 47823 [ ...

Page 7

... Crimping Dies 47820 through 47825, 47915, and 47918 Crimping Chamber Crimping Chamber GO Element GO element must pass NO-GO element may enter completely through the partially, but must not pass crimping chamber. completely through the crimping chamber. Figure 10 Rev H For additional information concerning the use of a plug gage, refer to Instruction Sheet 408– ...

Page 8

... Plate, Flare 45992-7 45992-8 45992-9 Plate, Flare, Lower 45992-4 45992-5 45992-6 Plate, Flare, Upper 47947 Die, Moving 47946 Die, Stationary 313336-3 Locator 2-306105-5 Screw 21018-5 Nut 2-21000-2 Screw 313322-2 Plate, Flare 304385 Plate, Flare, Lower Figure 11 Tyco Electronics Corporation View Rev ...