140-0000-951 Emerson Network Power, 140-0000-951 Datasheet - Page 233

DIE SET MCX/SMB/SMC/SMA 75OHM SM

140-0000-951

Manufacturer Part Number
140-0000-951
Description
DIE SET MCX/SMB/SMC/SMA 75OHM SM
Manufacturer
Emerson Network Power
Datasheets
1.140-0000-952.pdf (1 pages)
2.133-3711-801.pdf (294 pages)

Specifications of 140-0000-951

Connector Type
MCX, SMB, SMC, SMA, 75 Ohm SMB
Crimp Handle
J572-ND
Crimp Or Cable Size
RG/U-178, 316, 316DS, 58, 142, 735A, LMR-100, LMR-195, LMR-200
Product
Crimping, Stripping & Cutting Tools & Drills
Description/function
Die for (RG 178, 316/DS, 58, 142, 735A, LMR-100, 195, 200)
For Use With
J572 - ACC FRAME FOR HAND CRIMP TOOL
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
1400000951
J573
Right Angle SMA Low Loss
Diameter .195, .200 and .240
Connectivity Solutions
Tel: 800-247-8256
•
Fax: 507-833-6287
LOW LOSS DIA.
0.195
0.200
0.240
Assembly Instructions
1. Identify connector parts. (3 piece parts)
2. Strip cable to dimensions shown. Do not nick braid, foil or center
3. Flare braid and slide body assembly over foil and dielectric,
4. Arrange braid uniformly around crimp stem. Slide crimp sleeve
conductor. Cut foil flush with dielectric, do not remove foil. Make
sure that dielectric is clean and free from all particles. Tin cen-
ter conductor, keeping solder amount to a minimum. Slide crimp
sleeve onto jacket of cable.
then under braid. Make sure cable center conductor is con-
tained within connector contact, but do not allow foil and
dielectric to enter body access port. Solder center conductor to
contact through the rear access port. Use a minimum amount
of solder for a full fillet joint. .020 (0.51) Diameter solder is
recommended.
forward and crimp using Johnson hand crimp tool 141-0000-
913 and recommended crimp die hex. Place expansion cap in
access port and seat with recommended Diameter flat punch.
•
.110 (2.79)
.110 (2.79)
.135 (3.43)
www.EmersonNetworkPower.com/connectivity
“A”
INCHES (MILLIMETERS) • CUSTOMER DRAWINGS AVAILABLE ON REQUEST
CABLE GROUP
LMR-195
LMR-200
LMR-240
LMR-195
LMR-200
LMR-240
LMR-195
LMR-200
LMR-240
CRIMP DIE HEX
.213 (5.41) hex
.213 (5.41) hex
.255 (6.48) hex
142-0407-101
142-0407-106
142-4439-101
142-4439-106
142-0435-101
142-0435-106
142-5407-101
142-5407-106
142-0439-101
142-0439-106
142-5435-101
142-5435-106
142-4407-101
142-4407-106
142-5439-101
142-5439-106
142-4435-101
142-4435-106
PART NO.
FLAT PUNCH DIA.
.187 (4.75)
.187 (4.75)
.242 (6.15)
CRIMP HEX
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.255 (6.48)
.255 (6.48)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.255 (6.48)
.255 (6.48)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.255 (6.48)
.255 (6.48)
233