1-47387-0 Tyco Electronics, 1-47387-0 Datasheet

no-image

1-47387-0

Manufacturer Part Number
1-47387-0
Description
TOOL HEAD CRIMP 16-14AWG PIDG
Manufacturer
Tyco Electronics
Series
PIDG™, Plasti-Grip™r
Datasheet
1.1-47386-0.pdf (9 pages)

Specifications of 1-47387-0

Connector Type
Terminals and Splices
Crimp Handle
1213563-1, 1213804
Crimp Or Cable Size
14-16 AWG
Lead Free Status / RoHS Status
Not applicable / Not applicable
Crimping Heads 1–46121–0, 1–47386–0, 1–47386–4,
1–47387–0, 1–47387–7, 1–525690–0, and
1–525691–0 are designed to crimp PIDG Terminals
and Splices, and PLASTI–GRIP Terminals and
Splices onto solid or stranded copper wire size 26–14
AWG. Refer to Figure 2. The crimping heads are
used with Double Action Battery Powered Hand Tool
Kits 1213804–[ ].
This instruction sheet provides recommended
procedures for wire preparation, crimping head
installation, crimping, and maintenance and
E
The crimping heads can also be used with the
626 Double Action Pneumatic Tool Adapter
1213563-1.
Figure 1
inspection. For information concerning tool setup and
operation, refer to Customer Manual 409–10056
packaged with the battery tool kit.
Reasons for reissue are provided in Section 8,
REVISION SUMMARY.
The crimping head consists of integral jaws which
close in an arc–like motion. After an operator locates
the terminal or splice between the crimping jaws and
inserts the stripped wire, the tool is activated to crimp
the terminal or splice to the wire.
Dimensions are in metric units with [inches in
brackets]. Figures and illustrations are for
reference only and are not drawn to scale.

1-47387-0 Summary of contents

Page 1

... Reasons for reissue are provided in Section 8, REVISION SUMMARY. The crimping head consists of integral jaws which close in an arc–like motion. After an operator locates the terminal or splice between the crimping jaws and inserts the stripped wire, the tool is activated to crimp the terminal or splice to the wire. ...

Page 2

... HEAD HEAD NOTE: Refer to Tyco Electronics Catalog 82042 for product part numbers. 3. HEAD INSTALLATION AND REMOVAL 3.1. Head Selection The crimping heads are coded to match the terminal and splice insulation color. Observe the embossed dots on the insulation of finished crimps to ensure that ...

Page 3

... Never place anything within the crimping jaws except Tyco Electronics terminals or splices. 4.1. Terminal Crimping Procedure 1. Strip wire to dimensions shown in Figure 2. DO NOT nick wire strand or use wires with nicked or missing conductor strands. 2. Center the terminal or splice wire barrel in the appropriate crimp chamber ...

Page 4

... To crimp the other half of the butt splice, reposition it in the crimping jaws and repeat Steps 1 through 5. If the splice cannot be turned, rotate crimping head. See Figure 4B. 7. Refer to Section 5 and Figure 6 for crimp inspection. 4A PIDG Butt Splice C" B" B" Equals Wire Barrel C" ...

Page 5

... Remove dust, moisture, and other contaminants with a clean, soft brush lint–free cloth. Do NOT use objects that could damage the head. 2. Make sure that all pins, rings, and other components are in place and secure. ...

Page 6

... NOTE 6 PIDG and PLASTI-GRIP Terminal and Splice Crimping Heads Crimp Inspection ACCEPT REJECT PIDG Insulation Restricting Terminals PIDG and PLASTI-GRIP Terminals PIDG Butt Splice Figure 6 408-10029 A ...

Page 7

... JAW CRIMPING CLOSURE HEAD HEAD DIMENSIONS 0.889-1.397 1-525690-0 [.0350-.0550] 1-47386-0 0.762-1.270 1-47386-4 [.0300-.0500] 1-47387-0 1.016-1.524 1-47387-7 [.0400-.0600] 0.762-1.270 1-46121-0 [.0300-.0500] 1.143-1.651 1-525691-0 [.0450-.0650] DANGER Disconnect the battery and remove crimping head from tool before inspecting crimping chambers ...

Page 8

... CUSTOMER SERVICE (38–35) TYCO ELECTRONICS CORPORATION P.O. BOX 3608 HARRISBURG, PA 17105–3608 For further repair and replacement information, call the Tyco Electronics Tooling Assistance Center at the number at the bottom of page 1. 8. REVISION SUMMARY S Initial release of document Inspection of Insulation Crimping Section Wire Barrel Jaws ...

Page 9

... PART NUMBER FOR CRIMPING HEAD ITEM NO. 1-47387-0 1-47386-0 1 45965-6 302993 2 9-305927-1 9-305927-1 3 302994 302994 4 301201 301201 5 39207 39207 A Rev PIDG and PLASTI-GRIP Terminal and Splice Crimping Heads 2 1 CUSTOMER REPLACEMENT PARTS 1-47386-4 1-47387-7 1-46121-0 1-525690-0 1-525691-0 3-304052-6 525355-8 LOCATOR 3-306105-9 9-305927-1 SCREW, 8- ...