576711 Tyco Electronics, 576711 Datasheet - Page 4

• Manufacturer Part Number: 576711
• Description: MATRICE DIE ASSY 24-22AWG
• Manufacturer: Tyco Electronics

Specifications of 576711

• Lead Free Status / RoHS Status: Not applicable / Not applicable

4 of 6
576720
576715
576714
576716
576742
576723
576711
PIDG STRATO-THERM Terminal Crimping Dies
Closure Configurations
SET
DIE
Insulation Barrel Die
6. With the wire barrel dies bottomed, check the
wire barrel crimp die closure using the proper plug
gage. Hold the gage in a straight alignment with
the die closure and carefully try to insert, without
forcing the GO member, and then the NO–GO
member. See Figure 6, Detail A. The GO member
must pass completely through the insulation and
wire barrel crimp die closures.
7. The NO–GO member may enter partially, but
must not pass completely through the wire barrel
crimp die closure. See Figure 6, Detail A.
8. Remove the moving die from the tool die holder.
9. Reposition the insulation adjustment spacers in
the No. 1 position. Refer to Paragraph 2.4 for
insulation crimp position adjustment procedures.
10. Insert the moving die into the tool die holder.
Closure Configurations
Wire Barrel Die
2.591-2.598 [.1020-.1023]
2.591-2.598 [.1020-.1023]
3.048-3.056 [.1200-.1203]
3.124-3.132 [.1230-.1233]
3.327-3.335 [.1310-.1313]
3.683-3.691 [.1450-.1453]
4.775-4.783 [.1880-.1883]
WIRE BARREL CRIMP CHAMBER
GO
GO Dimension
GO Dimension
2.690-2.692 [.1059-.1060]
2.690-2.692 [.1059-.1060]
3.147-3.150 [.1239-.1240]
3.223-3.226 [.1269-.1270]
3.426-3.429 [.1349-.1350]
3.782-3.785 [.1489-.1490]
4.874-4.877 [.1919-.1920]
NO-GO
Tyco Electronics Corporation
Figure 5
0.813-0.820 [.0320-.0323]
1.067-1.074 [.0420-.0423]
0.940-0.947 [.0370-.0373]
0.940-0.947 [.0370-.0373]
1.067-1.074 [.0420-.0423]
1.067-1.074 [.0420-.0423]
1.676-1.684 [.0660-.0663]
4. REPLACEMENT PARTS
A complete inventory of customer–replaceable parts
for each die set assembly should be stocked and
controlled to prevent lost time when replacement of
parts is necessary. See Figure 7. Order replacement
parts through your Tyco Electronics Representative,
or call 1–800–526–5142, or send a facsimile of your
purchase order to 1–717–986–7605, or write to:
11. With the wire barrel dies bottomed, check the
insulation crimp die closure using the proper plug
gage in the same manner as steps 6 and 7. See
Figure 6, Detail B.
12. If both the wire barrel and insulation die
closures meet the GO NO–GO gage conditions,
the dies may be considered dimensionally correct.
13. If you find that the crimp die closures do not
conform with the GO NO–GO gage conditions,
contact your local Tyco Electronics Representative.
50.8 [2.000] Min. Typ
GO
INSULATION BARREL CRIMP CHAMBER
6.35 [.250] Typ
1.217-1.219 [.0479-.0480]
1.471-1.473 [.0579-.0580]
1.344-1.346 [.0529-.0530]
1.344-1.346 [.0529-.0530]
1.471-1.473 [.0579-.0580]
1.471-1.473 [.0579-.0580]
2.080-2.083 [.0819-.0820]
NO-GO
NO-GO Dimension
NO-GO Dimension
408-10039
WIDTH (W)
4.06 [.160]
4.39 [.173]
5.89 [.232]
5.89 [.232]
6.63 [.261]
6.63 [.261]
8.43 [.332]
W"
Rev B