576715 Tyco Electronics, 576715 Datasheet

576715

Manufacturer Part Number

576715

Description

MATRICE DIE ASSY 18AWG

Manufacturer

Tyco Electronics

Datasheet

1.576711.pdf (6 pages)

Specifications of 576715

Lead Free Status / RoHS Status

Not applicable / Not applicable

Available stocks

Company

Part Number

Manufacturer

Quantity

Price

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

5767153-9

Manufacturer:

TE Connectivity AMP Connectors

Quantity:

12 000

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

5767153-9

Manufacturer:

Murata

Quantity:

1 250

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

5767154-2

Manufacturer:

TE Connectivity AMP Connectors

Quantity:

12 000

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

5767154-2

Manufacturer:

TYCO

Quantity:

34 146

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

5767154-3

Manufacturer:

TE Connectivity AMP Connectors

Quantity:

12 000

Current page: 1 of 6
Download datasheet (441Kb)

This instruction sheet provides application

instructions, maintenance, and inspection procedures

for the dies listed in Figure 1. These dies will crimp

PIDG STRATO–THERM Terminals with a wire size

range of 24 thru 10.

Basic instructions on the use of these dies, die

adjustments, wire preparation, etc.; are provided in

Section 2, INSTRUCTIONS.

Section 3, MAINTENANCE and INSPECTION

PROCEDURES, enables you to establish and

maintain a die certification program.

Dies are coated with oil to prevent rust and corrosion.

Wipe this oil from the dies, particularly from the

crimping area. Instructions for Hand Tool 69710–1,

refer to Instruction Sheet 408–2095. For

recommended tooling used with these dies other than

Hand Tool 69710–1, contact Tyco Electronics Tooling

Assistance Center at the number listed at the bottom

of this page.

All dimensions on this document are in metric

units [with U. S. customary units in brackets].

Figures and illustrations are for reference only,

and are not drawn to scale.

Figure 1

Each set of dies consist of a moving die and a

stationary die. See Figure 1.

Loosen the die holding screws, and remove the dies.

Strip the wires to the dimensions provided in Figure 2.

1. Position the stationary die in the stationary die

holder. Tighten the die holding screw just enough

to hold the die in place. Do not tighten the screw.

2. Position the moving die in the moving die holder.

Tighten the die holding screw just enough to hold

the die in place. Do not tighten the screw.

3. With a terminal in position, insert the wire, then

squeeze the handles until the dies bottom.

4. Tighten both the die holding screws while dies

are bottomed. Tool is now ready for operation.

1. Place the terminal in the stationary die as shown

in Figure 3.

Refer to Figure 2 for wire strip length.

Check the die alignment and tighten the die

holding screws at least twice daily.

Refer to Paragraph 2.4 for die insulation crimp

adjustment.

Dies will not accommodate terminals with tongue

width exceeding 11.91 mm [.469 in.].

576715 Summary of contents

Page 1

... Instructions for Hand Tool 69710–1, refer to Instruction Sheet 408–2095. For recommended tooling used with these dies other than Hand Tool 69710–1, contact Tyco Electronics Tooling Assistance Center at the number listed at the bottom of this page. All dimensions on this document are in metric units [with U ...

Page 2

Finished Crimp Figure 2 2. Close the tool handles until the terminal is held firmly in place. 3. Insert a stripped wire into the terminal until the wire butts against the locator. 4. Complete the crimp by closing the handles ...

Page 3

... Broken Corner Figure 4 3.3. Die Closure Inspection Every Tyco Electronics die set is inspected and tested for proper die closure before being shipped from the factory. An inspection should, however, be performed periodically to measure the die closure. The die closure inspection is accomplished using the GO NO– ...

Page 4

... WIRE BARREL CRIMP CHAMBER DIE SET GO 576711 2.591-2.598 [.1020-.1023] 2.690-2.692 [.1059-.1060] 576720 2.591-2.598 [.1020-.1023] 2.690-2.692 [.1059-.1060] 576715 3.048-3.056 [.1200-.1203] 3.147-3.150 [.1239-.1240] 576714 3.124-3.132 [.1230-.1233] 3.223-3.226 [.1269-.1270] 576716 3.327-3.335 [.1310-.1313] 3.426-3.429 [.1349-.1350] 576742 3 ...

Page 5

... No. 1 Position Wire Barrel Dies Bottomed, but Not Under Pressure Adjustment Spacers in No. 3 Position GO" Gage Must Pass Completely Through Die Closure NO-GO" Gage May Enter Partially, but Must Not Pass Completely Through the Die Closure Figure 6 Tyco Electronics Corporation 408-10039 ...

Page 6

... ANVIL, Insulation 1 11 ANVIL 1 12 INDENTER, Barrel 1 13 LOCATOR 1 14 SPRING, Compression DIE SET NUMBERS 576711 576714 576715 576716 1-21046-3 1-21046-3 1-21046-3 1-21046-3 1-306027-5 306027-6 306027-6 306027-6 1-306027-6 306027-7 306027-7 306027-7 1-306131-6 1-306105-1 1-306105-1 1-306105-1 2-305832-8 2-305832-8 2-305832-8 2-305832-8 2-305832-9 2-305832-9 ...