576723 Tyco Electronics, 576723 Datasheet

no-image

576723

Manufacturer Part Number
576723
Description
MATRICE DIE ASSY 10AWG
Manufacturer
Tyco Electronics
Datasheet
1.576711.pdf (6 pages)

Specifications of 576723

Product
Punches & Dies
Lead Free Status / RoHS Status
Not applicable / Not applicable
This instruction sheet provides application
instructions, maintenance, and inspection procedures
for the dies listed in Figure 1. These dies will crimp
PIDG STRATO–THERM Terminals with a wire size
range of 24 thru 10.
Basic instructions on the use of these dies, die
adjustments, wire preparation, etc.; are provided in
Section 2, INSTRUCTIONS.
Section 3, MAINTENANCE and INSPECTION
PROCEDURES, enables you to establish and
maintain a die certification program.
Dies are coated with oil to prevent rust and corrosion.
Wipe this oil from the dies, particularly from the
crimping area. Instructions for Hand Tool 69710–1,
refer to Instruction Sheet 408–2095. For
recommended tooling used with these dies other than
Hand Tool 69710–1, contact Tyco Electronics Tooling
Assistance Center at the number listed at the bottom
of this page.
E
i
All dimensions on this document are in metric
units [with U. S. customary units in brackets].
Figures and illustrations are for reference only,
and are not drawn to scale.
Figure 1
Each set of dies consist of a moving die and a
stationary die. See Figure 1.
Loosen the die holding screws, and remove the dies.
Strip the wires to the dimensions provided in Figure 2.
1. Position the stationary die in the stationary die
holder. Tighten the die holding screw just enough
to hold the die in place. Do not tighten the screw.
2. Position the moving die in the moving die holder.
Tighten the die holding screw just enough to hold
the die in place. Do not tighten the screw.
3. With a terminal in position, insert the wire, then
squeeze the handles until the dies bottom.
4. Tighten both the die holding screws while dies
are bottomed. Tool is now ready for operation.
1. Place the terminal in the stationary die as shown
in Figure 3.
i
i
i
i
Refer to Figure 2 for wire strip length.
Check the die alignment and tighten the die
holding screws at least twice daily.
Refer to Paragraph 2.4 for die insulation crimp
adjustment.
Dies will not accommodate terminals with tongue
width exceeding 11.91 mm [.469 in.].

576723 Summary of contents

Page 1

... Instructions for Hand Tool 69710–1, refer to Instruction Sheet 408–2095. For recommended tooling used with these dies other than Hand Tool 69710–1, contact Tyco Electronics Tooling Assistance Center at the number listed at the bottom of this page. All dimensions on this document are in metric units [with U ...

Page 2

Finished Crimp Figure 2 2. Close the tool handles until the terminal is held firmly in place. 3. Insert a stripped wire into the terminal until the wire butts against the locator. 4. Complete the crimp by closing the handles ...

Page 3

... Broken Corner Figure 4 3.3. Die Closure Inspection Every Tyco Electronics die set is inspected and tested for proper die closure before being shipped from the factory. An inspection should, however, be performed periodically to measure the die closure. The die closure inspection is accomplished using the GO NO– ...

Page 4

... With the wire barrel dies bottomed, check the wire barrel crimp die closure using the proper plug gage. Hold the gage in a straight alignment with the die closure and carefully try to insert, without forcing the GO member, and then the NO– ...

Page 5

... No. 1 Position Wire Barrel Dies Bottomed, but Not Under Pressure Adjustment Spacers in No. 3 Position GO" Gage Must Pass Completely Through Die Closure NO-GO" Gage May Enter Partially, but Must Not Pass Completely Through the Die Closure Figure 6 Tyco Electronics Corporation 408-10039 ...

Page 6

... Figure 7 Tyco Electronics Corporation 408-10039 576720 576723 576742 1-21046-3 1-21046-3 1-21046-3 1-306027-5 306027-9 306027-6 1-306027-6 1-306027-0 306027-7 1-306131-6 2-306131-3 1-306105-1 2-305832-8 2-305832-8 2-305832-8 2-305832-9 2-305832-9 2-305832-9 2-306131-1 3-306131-4 ...