58268-2 Tyco Electronics, 58268-2 Datasheet

no-image

58268-2

Manufacturer Part Number
58268-2
Description
DIE SET ULTRA FASTPLUS 16-14AWG
Manufacturer
Tyco Electronics
Datasheet
1.58268-1.pdf (4 pages)

Specifications of 58268-2

For Use With
A27850CT - CONN RECEPT FAST 14-16 AWG .187A27850TR - CONN RECEPT FAST 14-16 AWG .187
Lead Free Status / RoHS Status
Not applicable / Not applicable
Crimping Die Assemblies 58268–1 and 58268–2 are
designed for use in the AUTO–PRO* Machine
818380–1 equipped with Applicator 818058–2. Each
die assembly, when installed in the machine, will
crimp Ultra–Fast Plus Fully Insulated FASTON*
Terminals 520401–[ ] onto wire sizes
No. 22–18 AWG (die assembly –1) and terminals
520402–[ ] onto wire sizes No. 16–14 AWG (die
assembly –2) .
These instructions provide specific information
regarding the die assemblies and applicable
terminals. For general performance of the machine,
refer to 408–9491, packaged with the machine. For
specific information on the applicator, refer to
408–8092.
E
Dimensions are in millimeters [with inch
equivalents in brackets]. Figures are for
identification only and are not drawn to scale.
Figure 1
Reasons for reissue are provided in Section 7,
REVISION SUMMARY.
Each die assembly consists of two stationary dies
(anvils) and two moving dies (crimpers) which when
closed form the crimping chamber. The stationary
dies feature a die holding screw and have the die
assembly part number marking. The moving dies
also feature a die holding screw and have the die
assembly part number, specific wire size, and
terminal type markings. See Figure 1.
The translucent color of the insulation on the terminal
indicates a specific wire range and must match the
wire size marking on the die assembly for crimping.
Refer to Figure 2.
The anvils and crimpers can be installed and removed
from the machine by tightening or loosening the die
holding screws. Refer to 408–8092 for specific
instructions on die installation and removal.
Refer to Figure 2 and select a terminal for the wire
of the specified size. Strip the wire to the length
TYPICAL .187 SERIES ULTRA-FAST
PLUS TERMINAL
NOTE:
To avoid personal injury, always disconnect
electrical and air supply before installing or
removing dies. Close lockout valve and apply
lock to prevent accidental cycling of machine.
Figure 2

58268-2 Summary of contents

Page 1

... Figure 1 Crimping Die Assemblies 58268–1 and 58268–2 are designed for use in the AUTO–PRO* Machine 818380–1 equipped with Applicator 818058–2. Each die assembly, when installed in the machine, will crimp Ultra–Fast Plus Fully Insulated FASTON* Terminals 520401–[ ] onto wire sizes No. 22– ...

Page 2

... Electronics does not manufacture or market these gages. To gage the crimping chamber, proceed as follows Crimping Die Assemblies 58268-1 and 58268-2 1. Remove traces of oil or dirt from crimping chamber and plug gage. 2. Mate the dies until it is evident that the dies have bottomed, then HOLD in this position. Do NOT force the dies beyond initial contact ...

Page 3

... Per EC 0990–0459–05: S Added the “F” Dimension to the table in Figure 3 S Updaterd format to current corporate requirements B Crimping Die Assemblies 58268-1 and 58268-2 É É É É É É É É É É É É GAGE ELEMENT DIMENSIONS WIRE BARREL CRIMP ...

Page 4

... Crimping Die Assemblies 58268-1 and 58268-2 15.82 [.623 REPLACEMENT PARTS DESCRIPTION SCREW, Die Holding RING, Retaining CRIMPER, Wire CRIMPER, Insulation ANVIL, Wire ANVIL, Insulation CRIMPER, Wire CRIMPER, Insulation ANVIL, Wire ANVIL, Insulation ...